Functions of the Terminals on Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent FVK1031-05

Question

Question:

There are three lugs on the 3-way FV1031-05 switch. I only remember two lugs being connected on the old switch. Unfortunately, I did not take a picture before I disconnected the old switch. do you have a wiring diagram for this switch when used with your RV ceiling vent fan?

asked by: Ted R

1

Helpful Expert Reply:

I will be happy to tell you the functions of the terminals on the back of Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent Item # FVK1031-05. The one labeled B is for battery power in. The terminal labeled C is the connection to the circuit board. And the M terminal goes to the fan motor.

expert reply by: Michael H

1

click to enlarge

Answer 1

For the Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent, part #FVK1031-05, the left terminal (B) is for the battery, the upper right (C) is for the circuit board, and the lower right (M) is for the motor. Refer to the picture below. The…

view full answer...

Answer 2

Yes, we do sell a replacement switch for the Fan-Tastic roof vent. The 3-Speed Switch for Fan-Tastic Vent Roof Vent item #FVK1031-05 replaces the 3-way switch in your vent.

view full answer...

Answer 3

If you need to replace the speed switch for the Fan-Tastic Vent Roof Vent FV801250 then you are needing part #FVK1031-05. Attached are some review videos for you to check out.

view full answer...

Answer 4

You can trace the connectors you have on your fan assembly to determine where they terminate in order to install the new switch #FVK1031-05. Why your old switch had only 2 of them connected I can't say unless it did not have all the functions…

view full answer...

Answer 5

If you for sure used a 3 speed switch like the #FVK1031-05 as a replacement switch it would appear that the wiring of the switch might be messed up. I'd check that to see if that allows the different speeds to function again. I attached a diagram…

view full answer...

Answer 6

The Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00 is the replacement for your Blade Assembly and Bow-Style Bracket with 14-3/8" blade diameter.

view full answer...

Answer 7

The 3 speed switch/controller part #FVK1031-05 that you referenced is the correct replacement for your Fan-Tastic vent model 6504/414 or 6504r/414. Based on what I was able to find on the numbers you listed the fan you have is the #FV803350 which the…

view full answer...

Answer 8

Most likely it is the switch of your Fan-Tastic roof vent like what the part #FVK1031-05 is designed to replace but you can try removing the two wires from your old switch and touching them together to test to see if it is the switch. If the fan…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Functions of the Terminals on Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent FVK1031-05

Product Page this Question was Asked From

Continue Researching