Troubleshooting Fan Switch Replacement of Fan-Tastic Roof Vent Where Only 1 Speed Works

Question

Question:

My fan-tastic fan model xw8100dm would slow down then speed back up. I changed the switch and the motor. Know it only runs one speed. What do I need to do to get my 3 speed switch to operate correctly. This is in my Itasca Meridian 2013. Thanks

asked by: Tommy T

1

Helpful Expert Reply:

If you for sure used a 3 speed switch like the # FVK1031-05 as a replacement switch it would appear that the wiring of the switch might be messed up. I'd check that to see if that allows the different speeds to function again.

I attached a diagram that shows how it should be wired.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Yes, we do sell a replacement switch for the Fan-Tastic roof vent. The 3-Speed Switch for Fan-Tastic Vent Roof Vent item #FVK1031-05 replaces the 3-way switch in your vent.

view full answer...

Answer 2

If you need to replace the speed switch for the Fan-Tastic Vent Roof Vent FV801250 then you are needing part #FVK1031-05. Attached are some review videos for you to check out.

view full answer...

Answer 3

I will be happy to tell you the functions of the terminals on the back of Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent Item #FVK1031-05. The one labeled B is for battery power in. The terminal labeled C is the connection to the circuit…

view full answer...

Answer 4

Your Dometic Fantastic Fan model 810034 will use the Replacement Fan Motor Assembly Kit #FVK8017-00. This is a direct replacement for your fan and will not require any modification.

view full answer...

Answer 5

For the Replacement 3-Speed Switch for Fan-Tastic Vent Roof Vent, part #FVK1031-05, the left terminal (B) is for the battery, the upper right (C) is for the circuit board, and the lower right (M) is for the motor. Refer to the picture below. The…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I sure can BJ. To add a keyless entry lock to your 2025 Airstream, I recommend the Bauer NE RV Entry Door Lock for Trailers item #BA33UR for a left handed lock or item #BA53UR for a right handed lock. These locks have Bluetooth capability and a PIN…

view full answer...

Troubleshooting Fan Switch Replacement of Fan-Tastic Roof Vent Where Only 1 Speed Works

Product Page this Question was Asked From

Continue Researching