Comparing the Stromberg Carlson # LG-3 and the Lippert Components # LC333964 Landing Gear Sets
Updated 06/26/2017 | Published 06/24/2017
Products Featured in This Question
Question:
I have a 2007 Dutchman 30foot with wheel RV trailer model #30CE-2S. I would like to replace the original landing system by using the current landing leg clamps without having to weld in a new setleg = 29-1/2inch long and the distance between the clamps is 17-1/2. Based on research at your site it indicates that the 6500# Stromberg Carlson LG-3 and the 6000# Lippert LC 333964 should be direct replacements for the existing system. Am I correct or should I consider purchasing other components?
asked by: Robert V
Expert Reply:
You are correct in your findings. Both sets of Landing Gear, the Stromberg Carlson # LG-3 and the Lippert # LC333964, have the standard weld stop locations where the inside to inside measurement is 15-1/2 inches and the outside to outside of the weld stop measurement is 17-1/2 inches and they measure 29-1/2 inches tall.
Either of these will fit the current brackets you have on your RV. One other thing you might want to note is that part # LG-3 has a total lift of 34-7/8 inches with travel being 19-7/8 inches and the drop leg being 15 inches. The part # LC333964 has a total lift of 37 inches with the travel being 21 inches and the drop leg being 16 inches. This will not affect how they fit on your RV, just how much lift they offer.
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 6001 - 7000 lbs
- Electric Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Ultimate Overview of the Stromberg Carlson Electric Landing Gear Set
- Video: Review of Stillwell Trailer Jack - Hydraulic Trailer Jack - ST74VR
- Video: Review of Premium - Dexter Trailer Jack - Dual Hydraulic Jack System - DX42CR
- Shop: Nerf Bars - Running Boards
- Shop: Andersen Trailer Jack Block - 8" Tall x 10" Wide
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Q&A: Can I Run Two Of The Dexter Self-Contained Hydraulic Jacks From The Same Remote?
- Search Results: andersen trailer jack block
- Search Results: hose caddy
- Search Results: 30 amp circuit breaker
- Shop: Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor
- Shop: Drop Leg for Lippert Power Jack - 8-11/16" Tall - 9" Diameter Footplate - Zinc
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Q&A: Replacement Landing Gear Motor for a 8532-07 Motor
- Q&A: Troubleshooting Landing Gear Motor that Works Slow on 2011 Keystone FZ302
- Q&A: Replacement Heavy Duty Motor For Landing Gear On 2010 Keystone Raptor Toy Hauler
- Q&A: Comparing Lippert Landing Gear Motor # LC196308 and Stromberg # LG-196308
- Q&A: Comparing the Stromberg Carlson Replacement Motors LG-196308 and LG-142178
- Search Results: lg~196308
- Shop: Spring-Loaded Pull Pins for Stromberg Carlson Landing Gear - Qty 2
- Shop: Atlas IV Vaquero Self-Contained Hydraulic Trailer Jack - 26" Lift - 10,000 lbs - Bolt On
- Search Results: landing gear pad
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Article: How to Measure for Trailer Hitch Drop
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
on Camper Jacks
