How to Remove a Roof Vent With a Continuous Hinge

Question

Question:

How to remove a continuous hinge pin in a roof vent

asked by: Serg

0

Expert Reply:

If you are asking how to remove a vent that has a continuous hinge then check out the video that I attached. One of our installers walks you through the steps of uninstalling your old roof vent with a continuous hinge and replacing it with the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents # BV0554-03.

expert reply by: Jon G

0

Bobby

5/21/2024

Where’s the video ?

Jon G.

5/21/2024

@Bobby A little further down the page, but I'm linking it to this comment as well so you can find it in multiple places.

Helpful Links

tv-install-ventline-enclosed-trailer-vent-cover-bv0554-03.aspx

Answer 1

Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer. The best way to find the correct replacement vent cover for your cargo trailer is to measure the vent. Most standard vents are…

view full answer...

Answer 2

You will first want to measure your vent, not the actual cover on your trailer. The vents are 14-1/2 by 14-1/2 inches, 14 by 14 inches, or 13 by 14 inches, in size. Then you will want to make sure the correct size cover uses the same type of hinge as…

view full answer...

Answer 3

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 4

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 5

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

Hey Edwin, The Skylight #SR89YR will work perfectly fine with your 1-1/4" thick roof on your 2018 Lance 1575, though they typically will require some trimming to the garnish to fit perfectly. You will want to pick up 2 tubes of self leveling…

view full answer...

Answer 8

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 9

Hello Lee, thanks for reaching out. If air won't go in at all it could be a bad/clogged valve. You could also have a major leak somewhere. Have you tried a soap test to see if there are any leaks?

view full answer...

Answer 10

For your Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter - Lippert 1621 and 0719 - 20,000 lbs #RP94720 you will need the Air System Service Kit for Reese Goose Box 5th Wheel to Gooseneck Air Ride Coupler Adapter #RP86007 which will…

view full answer...

Answer 11

Hello Marc, thanks for reaching out. The Intelli-Power converter/ charger Model PD9260C can only charge lead acid batteries, it will not work with lithium. That said, we do have a suitable replacement for this that is lithium compatible. For that I…

view full answer...

How to Remove a Roof Vent With a Continuous Hinge

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching