Torque Specs for Installing etrailer 10 x 2-1/4 Inch Electric Trailer Brakes

Question

Question:

What is the torque setting for the studs?

asked by: Mathew

1

Helpful Expert Reply:

The recommended torque spec for etrailer electric trailer brakes # AKEBRK-35-SA is 45 to 70 foot pounds. For compatible nuts and lock washers use # BRKH10B.

expert reply by: Michael H

1

Answer 1

Yes, I can help you with the install of the Dexter Breakaway and Parking Kit for Drum Brakes #T2385200 (Replaced the Titan 2385200) on your Dexter Electric Trailer Brake Assembly #K23-086-00. To install the parking brake cable, the cable is fed…

view full answer...

Answer 2

Hello Jose, thanks for reaching out. What I recommend for your are the Dexter Electric Trailer Brakes #K23-086-087-00. These are the standard 10" x 2.25" brakes and they are parking brake compatible. The Dexter brakes use the same 4 bolt…

view full answer...

Answer 3

Adding a brake controller to your 2024 Hyundai Palisade will require 7-way wiring. You can accomplish this using the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter #TK64CR. This kit comes with everything you need to…

view full answer...

Answer 4

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 5

The psi of your trailer tires will be listed on the side wall. It will list the max psi which is what you will want to fill them to regardless of how much weight you have. For reference, the 4.80 x 12 tires we carry have a 60 psi max for load range B…

view full answer...

Answer 6

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 7

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 8

Hi Jeff, welcome back! Is that the 126003? I don't see a 1260031 but the Lippert 126003 is a 3,500 lb hub with a 5 on 4-1/2 bolt pattern. Assuming that is correct, the Terran Axle Trailer Hub and Drum Assembly #TX68VJ will work as a replacement.…

view full answer...

Answer 9

I think I have a solution for you in the Global Link RV Entry Door Locking Latch Kit, #295-000021 for white or, #295-000019 for black. This latch kit measures 3.47" wide x 4.28" tall, fits doors that are 1-1/4" to 1-1/2" thick,…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...