What Frequency Does Prodigy RF Controller Operate on For Determining if Interference Will Occur

Question

Question:

I have a tire pressure monitoring system on my motorhome. Do you think the rf signals from the tpms will interfere with the brake controller. Thanks

asked by: Tom O

0

Expert Reply:

The RF signal from the tire pressure monitoring system will not interfere with the Bluetooth connection of the Prodigy RF brake controller # TK94FR. The frequencies will be different.

expert reply by: Jameson C

0

Answer 1

There is no difference between the two. We have two similar but different part numbers because we market the #BWGNRK1108 as a gooseneck hitch and the #BWGNRK1108-5W as the mount for the #BWRVK3400 sliding version of the B&W Companion 5th wheel…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hello Sean, Thanks for writing in. For a replacement hardware kit you will want to order the Replacement Hardware Kit for Trailer Hitches #RHK. Above "ADD TO CART" you will need to put "Curt C15410" so the warehouse knows what…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 11

Hey there Trace! There are parts of the steel brackets that come into contact with the aluminum bed on your new 2026 F350 Super Duty (congrats on the new truck by the way - those are super nice!). B&W says to use strips of polypropylene tape…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

What Frequency Does Prodigy RF Controller Operate on For Determining if Interference Will Occur

Continue Researching