Does LubriMatic Mini Grease Gun Require A Cartridge For Use

Question

Question:

Can the LubriMatic Mini Grease Gun with Straight Pipe - 12inch Hose be filled using suction as well as using the 3inch cartridge?

asked by: Tony A

1

Helpful Expert Reply:

The LubriMatic Mini Grease Gun # 30-800 like the part # L30-132-07 are not designed for a direct grease fill. It is designed to use the 3-oz cartidges like part # L54FR.

We do have grease guns that can be filled with suction or use a cartridge. They are part # L30100, part # L30-192, and part # L30193.

expert reply by: Jeffrey L

1

Answer 1

Hey Miles, thanks for reaching out! You'll need the TruRyde Electric Trailer Brakes #TRU36FR along with 2 of the Easy Grease Trailer Hub and Drum Assembly #AKHD-545-35-EZ-K in order to get your tow dolly equipped with electric braking…

view full answer...

Answer 2

There's a couple pieces of information you will need to know to determine if a brake setup like what we offer for trailers would fit your Stehl Tow Dolly. The first thing you will need to know is the bolt pattern of your current wheels. This is…

view full answer...

Answer 3

From what I could find online it does look like a Stehl tow dolly does require an electric brake controller like the Curt Echo #C51180 you referenced to operate. The battery that you are seeing in your picture is the Hopkins Engager Breakaway Kit…

view full answer...

Answer 4

The Primus IQ #TK90160 doesn't have instructions that come with a wiring diagram, but we have a picture/diagram on our site that shows which wires are connected to which functions on your vehicle. I attached the diagram for you to view, the wires…

view full answer...

Answer 5

The left side is the driver side, right side is passenger side. On a trailer brake assembly like #23-105 the arm that the magnet is on points to the front of the trailer and the magnet always will be on the bottom. I have included a picture that…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Does LubriMatic Mini Grease Gun Require A Cartridge For Use

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching