Parts Needed to Install SuperSprings on 2017 Chevrolet Silverado 1500

Question

Question:

Are the SS all I need or is there other parts to order?

asked by: Tom A

0

Expert Reply:

The SuperSprings Custom Suspension Stabilizer and Sway Control Kit # SSA28 is all you need. The kit includes all the necessary hardware for installation.

expert reply by: Charles S

0

David C.

7/18/2020

Looking at the #sa28 super springs custom suspension stabilizer and sway control kit. This is above the axle springs going on a 2017 Silverado 1500 Liz Short bed (6’ bed). Is it necessary to remove the leaf springs to install? Want to reduce wind impact sway towing 7600lb 5th wheel. Any other options. We currently have air bG support. Thanks

Chris R.

7/22/2020

There's no need to remove the factory leaf springs on your Silverado to install the SuperSprings # SSA28. Removing the rear wheel helps a bit with installation, but it's not required.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Answer 9

Hey Don, thanks for the information! That's a significant amount of sag and a pretty heavy trailer, I recommend the Hellwig Pro Series Helper Springs item #HE79FR for the higher 2,500 lbs capacity. I doubt you're driving around with your bed…

view full answer...

Answer 10

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Answer 11

Hey Kurt, yes the correct gap for SumoSprings Solo kits like the part #SS88UV is 1/2 inch to 1 inch like you mentioned. Did you install this already?

view full answer...

Parts Needed to Install SuperSprings on 2017 Chevrolet Silverado 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching