Trailair flex air 5th wheel pin box

Question

Question:

What is the measurement from the center of the front row of bolts to the center of the king pin for the Trailair Flex air 5th wheel pin box? part number LC328492

asked by: Dan S

0

Expert Reply:

I went out to the warehouse and was able to get the measurement you were looking for on the Trailair Flex Air 5th Wheel Pin Box - Lippert 1621 - 18,000 lbs, # LC328492. From the center of the front row of bolts to the center of the king pin it is 21-1/2 inches. I've attached a picture to help.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hey Todd, welcome back! The Curt Flex Air part #LC369535 that you referenced will be a great option for a cushioned pin box that will make a noticeable difference in ride quality. This does not sit 6 inches taller than your current Rota Flex so there…

view full answer...

Answer 2

A shorter pin box will reduce your turning clearance by bringing your trailer in closer so you don't want to do that. The longest pin box we have that fits a 1621HD bolt pattern is the Curt Air Ride 5th Wheel Pin Box item #LC158778. The center of…

view full answer...

Answer 3

If you have no identifiers on your 2016 Keystone Cougar 333MKS then the only way to determine the bolt pattern of your pin box is to either contact the manufacturer with the frame number, which is usually extremely time consuming, or to use our guide…

view full answer...

Answer 4

According to Lippert there are many factors that can effect air pressure such as the size of the air spring in diameter and height, the pin weight of the trailer, the mechanics of each individual hitch, altitude and air temperature. Lippert has…

view full answer...

Answer 5

The Greystone 26" Electric Fireplace with Crystal #324-000069 is the direct replacement for the F2625.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Trailair flex air 5th wheel pin box

Product Page this Question was Asked From

Continue Researching