Recommended Replacement Hub for Dexter 8-91A
Updated 07/02/2024 | Published 10/21/2016
Products Featured in This Question
Question:
I want to replace a trailer hub on a very old trailer. it is a 1.25 square axle. 61 inches long hub to hub. The hub on it is a dexter 8-81A. other numbers on the hub are 1731 and MTA 3 can you tell me which of your assemblies would replace this?
asked by: Jamie
Expert Reply:
I reached out to my contact at Dexter regarding the numbers you gave. They couldn't match anything and suggested that you most likely have a 8-91A, which is a 4 on 4 bolt pattern. That is a very basic trailer hub assembly and the replacement part is # 8-91-05UC1. This assembly comes with the L44643 bearings, the grease seal, the lugs and the grease cap.
I'd suggest a bearing packer like # PTW1218 and the Industrial Strength Grease # L11390.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44649 / L44649
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Q&A: Replacement Dexter Hub for 8-91A Hub
- Shop: etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 15-3/8" Lift - 2,500 lbs
- Video: Let’s Check Out the Washer For 1" Spindle
- Search Results: 2 5 16 ball
- Search Results: hitch extender
- Search Results: reducer
- Search Results: 6 inch extension hitch adapters
- Search Results: jack
- Search Results: coupler
- Search Results: heavy duty receiver hitch
- Q&A: Washer Needed to Install Dexter Trailer Idler Hub Assembly for 2,000-lb Axles
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: LubriMatic Prime Guard High Temperature Wheel Bearing Grease - Red - 16-oz Can
- Shop: Washer For 1" Spindle
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 15,000 lbs
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings - Pre-Greased
- Q&A: Replacement Bearings and Seals for a Dexter Hub with 8-91A Stamped on Back
- Q&A: How to Determine Correct Hub Replacement for 1994 Jayco Eagle SD with Dexter Axle
- Article: Trailer Tire Sizing
- Article: Slipper Spring Trailer Suspension System Review
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Trailer Hub - AKIHUB-440-2-EZ-2K
- Q&A: Recommended Swivel Jack For Trailer Tongue With Caster Wheel And Footplate
- Video: Trailer Wheel Measurements
- Q&A: Is a Spindle Washer Needed Between the Spindle Nut and Outer Bearing on Dexter 5 on 4-1/2 Hubs
- Q&A: How To Measure For Replacement Wheels For A Boat Trailer
Dan
7/2/2024
Jason, The product you linked (# 8-91-05UC1) shows it has L44649 bearings not L44643 bearings. Do you offer a product with the 8-91A hub with L44643 bearings? I was looking at item # AKIHUB-440-2-EZ-1K is it a match?