Replacement Dexter Hub for 8-91A Hub
Updated 06/05/2020 | Published 07/09/2016
Question:
I have a boat trailer that has Dexter 8 - 91A hubs on it. The bearings are both L44649s and the grease seal has a 1.25 I.D with a 1.9 O.D. I do not see this combination on your site. Would it be possible to get this set up? Thank you for your time.
asked by: Gordon B
Expert Reply:
If the hub that was on your trailer axle previously had 8-91A stamped on the back of it your spindle should require inner and outer bearings of # L44649 like you used. The part # 8-91-05UC1 SHOULD be an exact replacement.
However we need to double check your grease seal measurement. Double check to make sure you don't have a 1.5 inner diameter seal with outer diameter of 1.9. You can also measure the spindle where the seal rides as well.
The seal dimensions you mentioned are not ones that are standard which means most likely you don't have them.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44649 / L44649
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44649 Bearings
- Search Results: heavy duty receiver hitch
- Search Results: coupler
- Search Results: jack
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles - 4 on 4 - L44649 Bearings
- Shop: etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 29-1/8" Lift - Zinc - 2.5K
- Search Results: bearing buddy
- Search Results: bearing buddy 198
- Search Results: castle nut washer
- Search Results: reducer
- Shop: Grease Seal
- Q&A: Recommended Replacement Hub for Dexter 8-91A
- Shop: CE Smith Post-Style Guide-Ons for Boat Trailers - 40" Tall - White - 1 Pair
- Q&A: Replacement Bearings and Seals for a Dexter Hub with 8-91A Stamped on Back
- Shop: Kenda Karrier KR35 ST205/75R15 LRD Radial Trailer Tire w/ 15" Black Mod Wheel - 5 on 4-1/2
- Shop: Buyer's Products Bolt-On 2-1/2" Hitch Receiver Tube - 20K
- Q&A: Replacement Trailer Idler Hub For Dexter 8-91A Hub With 4 on 4" Lug Pattern
- Q&A: Needing Dexter Hub # 8-91A
- Video: Dexter Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles Feature Review
- Video: Review of Optronics Amber Trailer Light Lens - A44AB
- Video: Hands-On with the U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles
- Shop: Trailer Wiring
- Q&A: Replacement Axle for Harbor Freight Trailer 4x8 Foot 1195 lb Capacity
- Shop: Base Plate for Tow Bar
- Shop: Tonneau Cover
- Q&A: Recommended Replacement Axle for Harbor Freight Folding Trailer 62671
- Video: A Closer Look at the Pack'Em Trimmer Rack for Enclosed Trailers
- Shop: Trailer Hitch
- Q&A: Recommended Swivel Jack For Trailer Tongue With Caster Wheel And Footplate
- Shop: Gooseneck Hitch
Bob D.
6/2/2020
I have a 1986 Starcraft Starlite 17 pop up that I am looking to replace the hub assemblies on. Dexter hub #8-91A. 4" bolt pattern, 1.500" & 1.062" diameter spindle, front & rear bearing # L 44549. Hub height 4.125", grease seal National 474476. Would this assembly be a direct replacement?