How to Wire the Lights in the Optronics Tail Light Kit # TL29BK
Published 09/02/2010
Question:
how do you install the wiring into thelight assembly
asked by: mike
Expert Reply:
Installation of the wires into the Standard Trailer Light Kit with 25 foot Wire Harness, item # TL29BK, is fairly simple, plug the corresponding wires on the # TL29BK kit into the upper (larger) holes on the back of the taillights. There are two holes for tail/brake lights and running lights. These holes are labeled. The wires should be stripped prior to insertion. The yellow wire goes on the left and is inserted into a tail/brake light port and the brown wire is inserted into a tail light port. On the right side the green wire is inserted into a turn/brake light port and the brown wire is inserted into a tail light port.
The lower (smaller) set of holes are there to allow removal of the wires if need be. You would stick a small round object into the lower hole and press, releasing the wire. After inserting the wires they should be routed along the indention in the light housing when mounted to avoid crushing the wires.
We have a video that details the wire installation near the end, for you to review.
Product Page this Question was Asked From
Standard Trailer Light Kit with 25' Wire Harness
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- License Plate
- Marker
- Square
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 5L x 4-1/2W Inch
- Amber
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Standard Trailer Light Kit with 25' Wire Harness
- Video: Ultimate Overview of the Standard Trailer Light Kit with 25' Wire Harness
- Video: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness Feature Review
- Video: Complete Breakdown of the Standard Trailer Light Kit with 25' Wire Harness
- Q&A: What is the Difference Between Over 80 inch and Under 80 inch Trailer Tail Lights
- Q&A: Parts Needed to Completely Re-Wire 20-Foot Cattle Trailer with Light and Reflectors
- Q&A: Recommended Trailer Wiring for 5x10 Trailer with 4-Way Trailer Connector
- Q&A: How to Wire a Ground Wire to a Trailer Light that Grounds Through Mounting Hardware
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Shop: Peterson Light Kit for Trailers Under 80" Wide - 20' Harness - Driver and Passenger
- Shop: Mini LED Identification Light Kit for Trailers Over 80" Wide - Submersible - Red LED/Lens
- Shop: Optronics Trailer Light Kit for Trailers over 80" Wide - Submersible - 25' Wiring Harness
- Shop: Optronics Fleet LED Trailer Tail Lights w/ Grommets - Stop,Turn,Tail - Submersible - Oval - Qty 2
- Shop: Replacement Tail Light Bracket for CE Smith Boat Trailer - Galvanized Steel - 4-1/2" Long
- Q&A: How to Find the Correct Bearing Buddy
- Q&A: Should Trailer Ground Wire Ran to Frame be Sanded Down to Bare Metal
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Shop: Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Video: Measuring To Choose The Right Trailer Axle
on Trailer Lights
