Width of the Replacement Track End Cap 853-5361

Question

Question:

How wide are these end caps?

asked by: JM

0

Expert Reply:

The width of the # 853-5361 is 1-5/8 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I spoke with Yakima, and they informed me that the t-track on the Yakima LockNLoad Platform Rack for Crossbars #Y05045-39 measures 8mm (.31") high, and measures 11mm (.43") wide. Attached is a diagram of depicting these measurements for you…

view full answer...

Answer 2

We currently offer replacement end caps for two different brands of roof mounted tracks, Yakima part #Y8810103 and Thule part #853-5361. The tracks can be hard to identify and I do know that Thule did produce these for A.R.E. Camper Shells so if the…

view full answer...

Answer 3

The only replacement end caps available for the Yakima Roof Rack Track Systems are the Replacement EndCaps #Y8810103. These caps feature a width of just over 1-5/8 inches. If you can tell me the model number of your Yakima tracks, or if they happen…

view full answer...

Answer 4

The Yakima Replacement Anchor Plate Style-A, Part #Y8810074, comes as a set of 8 plates that measure 3/4-inch x 7/8-inch. The centered threaded hole measures 0.2 inches (or 5.1 millimeters) in diameter. Please refer to the photo provided. The Yakima…

view full answer...

Answer 5

The difference between the Yakima HD Crossbars like the #Y74MR and the regular Yakima Tracks like the #Y01135 is that they are compatible with different feet and adapters. With the HD tracks, they will fit the Yakima Skyline towers, OverHaul HD…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Width of the Replacement Track End Cap 853-5361

Product Page this Question was Asked From

Continue Researching