Will Roller part # YR12243-5 Fit on Roller Bracket # CE10305G
Updated 05/16/2016 | Published 05/12/2016
Products Featured in This Question
Question:
1. Will a 12inch Yates Side Guide Roller code YR12243-5 fit into the 12inch bracket code CE10305G and still spin? If not can one cut 1/2inch off the end of the roller without damage to the roller? Or should I get a shorter roller? 2. Will a 5/8inch shaft code CE10727A fit into the 5/8inch hole down the center of the 12inch roller YR12243-5? If so, will the roller still spin on the shaft or will it be tight so that the shaft just spins inside the holes in the 12inch bracket code CE10305G? 3. Can the 12inch Yates Side Guide Roller code YR12243-5 be used as a horizontal bottom roller to support a 500 pound boat? 4. What is the distance between the outside of the 6x12inch plate on the 12inch bracket code CE10305G vertically up to the top of an installed 12inch roller code YR12243-5? 5. What is the distance between the center of the 5/8inch holes and closest outside edge of the 6x12inch plate on a 12inch bracket CE10305G? 6. Do you sell the 5/8inch shaft and Pal Nuts code CE10727A in stainless steel? If not, will it rust, jam and become useless?
asked by: James N
Helpful Expert Reply:
The 12 inch roller part # YR12243-5 that you referenced is designed to fit the CE Smith Panel Bracket # CE10305G. You would just need the roller shaft part # CE10727A which comes with pal nuts and you would be set. There isn't a stainless steel version of this available but this will resist corrosion well since it is galvanized. The roller will spin easily and would work well.
This would work well for a roller on a boat trailer for a 500 lb boat.
4-1/4 inches is the distance from the mounting flange on the bracket to the tallest portion of the roller when installed.
Product Page this Question was Asked From
Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12" Long - 5/8" Shaft
- Boat Trailer Parts
- Rollers
- Side Guide Roller
- 2-1/2 Inch Diameter
- Rubber
- 12 Inch Long
- Fits 5/8 Inch Shaft
- Yates Rubber
more information >
Continue Researching
- Video: Yates Endcap for Side Guide Rollers Review
- Shop: Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 12" Long - 5/8" Shaft
- Shop: Yates Endcap for Side Guide Rollers - Heavy-Duty Rubber - 5/8" Shaft - Qty 1
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer tires and wheels
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: Trailer Lighting Requirements
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Search Results: trailer wiring
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs
- Article: Trailer Tire Sizing
- Search Results: trailer lights
- Article: How to Tell the Weight Rating of a Trailer Axle
- Search Results: trailer leaf springs
- Shop: Americana Trailer Wheel Lug Nut - Chrome Plated - 1/2"-20
- Search Results: trailer hitch ball mount
- Q&A: How Much Roller Shaft Length will Yates Endcap for Side Guide Rollers # YR224-4 End Up Taking up
- Q&A: Replacement 6" x 2" Roller for Older Boat Trailer
- Q&A: Can the Yates Side Guide Roller # YR12243-5 be Cut for a Specific Length
- Q&A: Replacement Rollers For 1965 Vintage Boat Trailer