How Much Roller Shaft Length will Yates Endcap for Side Guide Rollers # YR224-4 End Up Taking up

Question

Question:

how much additional shaft length is needed for using roller end caps

asked by: John

0

Expert Reply:

I went out and pulled a Yates Endcap for Side Guide Rollers # YR224-4 from our warehouse to measure it and found that it is going to take up 1-3/8 inch of roller shaft space.

expert reply by: Jameson C

0

Answer 1

While there is no specific kit for switching your 98 Shoreland'r from rollers to bunks, it should be relatively straight forward. It looks like your rollers should be bolted on, so you should be able to remove those and then add bunks. You will…

view full answer...

Answer 2

This can absolutely be done. While there are not "kits" for doing the conversion, we do have the parts that you will need. These are not kitted together because each boat/trailer combination is different, so it is easier to not kit them. It…

view full answer...

Answer 3

We have just what you need. For the two 5' bunk boards I recommend the CE Smith Carpeted Bunk Boards for Boat Trailers - 5' Long - 1 Pair #CE27820, but the longest board we offer is 7' so for the two 109" boards you will need to get…

view full answer...

Answer 4

For the bunks I recommend using two sets of the 5' CE Smith Carpeted Bunk Boards #CE27820, or you'd like to get your own wooden boards you can wrap them in Marine-Grade Carpeting #CE11349. To install the boards, you will need a pair of…

view full answer...

Answer 5

Yes, it is possible to switch from center rollers to bunk rollers on a boat trailer. For this, you will first need to remove the center rollers and then you can install a set of bunk rollers, part #CE27710 along with part #CE10000G-4 to support the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How Much Roller Shaft Length will Yates Endcap for Side Guide Rollers # YR224-4 End Up Taking up

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching