Hitch Pin Wearing Out on Blue Ox SwayPro Weight Distribution Using a 2-1/2 to 2 Inch Reducer Sleeve
Updated 05/03/2016 | Published 04/30/2016 >
Question:
I have a 2015 Ram 3500 and a BlueOx 15000# distribution hitch pulling a 14000# rated flat bed trailer loaded well with in specs. The hitch was purchased through your company with the help of a fine fellow name Mike, though the last name escapes me at the moment. I have a fair amount, in my opinion, on the hitch pins after trips of say 4000 miles and these are new pins, both locking and non locking. The truck had the 2.5inch reciever and the factory 2.5inch to 2inch reducer. This wear on the pin concerns me that I may see a failure. I have thought of using a grade 8 fine thread bolt as an alternative. Any thoughts.
asked by: Craig
Expert Reply:
If you could please email me some pictures of the pin so I can see what is going on. Hitch pins and bolts don't have official capacities (though some bolts/locks might) because their actual capacity exceeds what most trailer hitches are rated for; even 2-1/2 inch hitches.
The problem is likely due to the use of the reducer sleeve which would allow for some play and extra movement that could be wearing down the hitch pin. My recommendation is to go with the 2-1/2 inch shank for Blue Ox SwayPro systems, # BXW4028. This will eliminate the need for the reducer sleeve and by removing that part of the equation there would be less movement and thus less wear on the pin.
Product Page this Question was Asked From
Blue Ox SwayPro Weight Distribution Shank for 2-1/2" Hitch - 9" Long - 9 Hole Adjustment
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 1900 lbs TW
- Fits 2-1/2 Inch Hitch
- SwayPro
- Blue Ox
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: In-Depth Review of the B and W Anti-Rattle Clamp for 2-1/2" Hitch Receivers
- Search Results: hitch anti~rattle
- Search Results: trailer hitch ball mount
- Search Results: 2 1/2 ball mount
- Shop: Trailer Wiring
- Shop: Truck Bed Camera
- Shop: Curt Anti-Rattle Hitch Clamp for 2-1/2" Hitches
- Shop: Gen-Y Anti-Rattle Clamp for 3" Hitch Receivers
- Shop: BulletProof Hitches Anti-Rattle Clamp for 2-1/2" Hitch
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Gen-Y Glyder Shock Absorbing Ball Mount for 2" Hitches - 2" Drop - 7K
- Shop: Gen-Y Anti-Rattle Clamp for 2-1/2" Hitch Receivers
- Shop: Blue Ox SwayPro Weight Distribution Shank for 2-1/2" Hitch - 9" Long - 9 Hole Adjustment
- Q&A: Is Gold Connector Needed with the Voyager Antenna Extension
- Q&A: Troubleshooting Limited Signal with Furrion Vision S Wireless RV Backup Camera
- Search Results: rear camera
- Search Results: tpms
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)


