Is a Sealant Required When Installing New Grease Seals in a Trailer Hub

Question

Question:

What is the recommended sealant to use with these grease seals for installation with a Dexter EZ Lube hub assembly kit?

asked by: Jay H

0

Expert Reply:

You do not have to use a sealant of any king when you install a grease seal like the part # RG06-050.

Check out the video I attached that shows the install of bearings and seal like the one you referenced.

expert reply by: Jameson C

0

Answer 1

Yes, you can replace your load range C tires with load range D tires without issue. It will only become any issue when you go down load ranges, not up. The tires will have the same overall diameter as long as they are the same size regardless of…

view full answer...

Answer 2

The TruRyde Spindle Nut #165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist.…

view full answer...

Answer 3

Yes. The hub group associated with the Dexter D35 axles use 10-19 seals. Set #RG06-050 includes two 10-19 seals. I have linked a video review of these seals for you.

view full answer...

Answer 4

Sealant is not required when installing a grease seal, like #RG06-050 you referenced. The cap will not need a sealant either. See the help article I've attached that explains the entire process of replacing bearings, races, and seals. I've…

view full answer...

Answer 5

I believe you are referring to the manual for various Dexter hub assemblies that call for the application of Permatex sealant or equivalent prior to the installation of a new seal. While I don't recommend going against the manufacturer's…

view full answer...

Answer 6

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is a Sealant Required When Installing New Grease Seals in a Trailer Hub

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching