What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?

Question

Question:

What size socket works with this castle nut?

asked by: Carl

0

Expert Reply:

The TruRyde Spindle Nut # 165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist. You don't want to torque these down tight as you do want to have slight movement and the cotter pin will keep it in place.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hey TJ! Yes, Dexter does have a bearing kit that will fit your axle #7359765. It is the Dexter Bearing Kit for 1-1/16" to 1-3/8" Tapered Spindle #DX76ER. However, they don't actually make these bearings. For the price, you're better…

view full answer...

Answer 2

Hey Jon, Most trailer wheel and tire combos - like the Kenda Karrier #KE69JV - do not come pre-balanced. Typically, trailer owners don’t worry about balancing since trailers don’t ride as smoothly as passenger vehicles and you’re not feeling that…

view full answer...

Answer 3

In order to re-pack the bearings on your trailer, all you will need is the grease, bearing packer, and grease gun: - LubriMatic LMX Industrial Strength Grease - 14 oz. Cartridge #L11390 - Powerbuilt Deluxe Bearing Packer #ALL647646 - LubriMatic…

view full answer...

Answer 4

EZ Lube Dust Caps, like #DC200L-DCRP, have a rubber plug that can be removed to access the zerk fitting. The rubber plug can be removed by gently prying it up with a flathead screwdriver. If your dust cap is in good condition and you want to avoid…

view full answer...

Answer 5

3500 lb axles have the most common and most consistent spindle sizes. They are typically 1.73 inches at the seal, 1.38 inches at the inner bearing and 1.06 inches at the outer bearing like #TRU24FR. I've attached a video to assist. I've…

view full answer...

Answer 6

The correct replacement bearing kit for a 6,000 lb Dexter axle is the following: - Bearing Kit #BK3-100 This comes with the correct replacement bearings, races, and seal for one hub, so you'd need a quantity of two bearing kits for one axle.

view full answer...

Answer 7

Hello Shelly, thanks for reaching out. We offer a lot of different hubs so we should have something that will work for you. I was not able to find any references for those part numbers though, so a bit more investigating will be needed to find the…

view full answer...

Answer 8

Thank you for providing that helpful information. The replacement will depend on the bolt pattern you are looking for. If you need a 5 on 4-1/2 bolt pattern we have the Trailer Idler Hub Assembly for 2K Axles - 13" to 15" Wheels - 5 on…

view full answer...

Answer 9

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 10

If your Carson trailer uses a standard spindle, you will need the Dexter Trailer Hub Assembly, #84550BX. This hub assembly includes lug nuts, L68149 inner bearing and race, L44649 outer bearing and race, grease cap and grease seal. If you have a…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The rattle or play you experienced is very common and the solution isn't to replace the ball mount with a tighter fitting one as that's not really possible but is to use an anti-rattle device like the part #63232. This installs in the shank…

view full answer...

What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching