Is Sealant Needed When Replacing Grease Seals and Dust Caps
Updated 11/30/2016 | Published 11/29/2016
Question:
Grease seal question - specifically Grease Seal - Double Lip - ID 1.719inch / OD 2.565. I watched the video and no silicone gasket seal was used when replacing the grease seal. And the outer edges do not appear to be covered with viton or similar. Is this ok? Some books recommend using silicone sealant on the grease seal but none on the dust cap? Doesnt make sense to me. Thanks.
asked by: Jerry
Expert Reply:
Sealant is not required when installing a grease seal, like # RG06-050 you referenced. The cap will not need a sealant either. See the help article I've attached that explains the entire process of replacing bearings, races, and seals. I've also attached a video on repacking bearings and installing grease seals you may find helpful.
Product Page this Question was Asked From
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.72 Inch I.D.
- 2.57 Inch O.D.
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: retainer clip
- Search Results: tall boy jack
- Search Results: national seal
- Search Results: 3500 lbs axle trailer bearings races seals caps
- Search Results: jack
- Search Results: 3500 lbs axle trailer brakes
- Search Results: brake hose
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: Timken Grease and Oil Seal - Double Lip - I.D. 1.719" / O.D. 2.565" - 473336
- Shop: Kwikee Electric RV Step Complete Assembly - Double - 32 Series - 24" Wide
- Video: Comprehensive Review: Grease Seal
- Q&A: Check Valve Replacement for Lippert Hydraulic Slide Out
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Video: Hands-On with the Kodiak Hydraulic Brake Hose
- Video: Kodiak Hydraulic Brake Hose Feature Review
- Video: Let’s Check Out the Dexter Hydraulic Brake Line with Fittings
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Kwikee Electric RV Step Complete Assembly Feature Review
- Video: Breaking Down the Replacement Lippert Motor Harness for In-Wall RV Slide-Outs
- Video: Breaking Down the Kodiak XL ProLube Oil Bath Hub Body and Cap
- Shop: Trailer Wiring
- Q&A: What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?
- Q&A: Can a Load Range C Tire Be Replaced with a Load Range D Tire
- Q&A: Nut Size Used on Dexter 3500 lb Hub and Drum Assembly
- Q&A: Replacement Seals for Hubs on Dexter D35 Axle
- Q&A: Using Gasket Maker on Grease Seals
- Q&A: Grease Cap and Dust Cap Needed for Trailer Bearings