Getting Power to 12-Volt Accessory Pin on 7-Way Trailer Connector

Question

Question:

Hot wire to use for a ram elec trailer jack

asked by: Tom

1

Helpful Expert Reply:

To get power to the pin in the 1:00 position of the # PK12703 7-way trailer connector, you'd run a length of 10 gauge wire # 10-1-1 which is sold by the foot from the terminal for the 1:00 pin on the 7-way to the positive battery terminal, via a # 9510 40 amp circuit breaker. You'd need two # DW05741-1 ring terminals to connect to the breaker and a # 44-5356A ring terminal to connect at the battery.

expert reply by: Mike L

1

click to enlarge

Answer 1

To install the Small Coin Pattern Vinyl Flooring #TS97FR with the RV Flooring Adhesive #TS76FR you just need to make sure that your trailer floor is a bare wood so you have the best bonding of the adhesive as possible. Be sure to sweep it out really…

view full answer...

Answer 2

If your 2012 Jeep Wrangler Unlimited came with a 4-Way you will need to use 4 and 7 way installation kit #ETBC7. This is a hardwire installation but it does come with everything you will need for the installation. I have included some links that will…

view full answer...

Answer 3

While running the MaxxAir MaxxFan Deluxe #MA00-06401K requires about 4-1/2 amps. For startup it will pull around 9 amps.

view full answer...

Answer 4

I recommend using the 601 Flooring Adhesive in a 1 Gallon #TS76FR or 4 Gallon #TS26FR depending on your application. The 601 does not have the pressure sensitive requirements of the 801, 1 Gallon #TS86FR and 4 Gallon #TS58FR adhesives.

view full answer...

Answer 5

I do have a solution for you, but I think welding something to the floor is going to really limit where you can place things to have them tied down. I don't think you're going to be able to get away from the issue with galvanic corrosion…

view full answer...

Answer 6

To set your 2022 Volkswagen Tiguan R-Line up to tow you will need the following parts: Trailer Hitch - etrailer Hitch item #e43ZR 4-Way Wiring Harness - Curt T-Connector Vehicle Wiring Harness item #C56403 Ball Mount Kit - Curt Towing Starter Kit for…

view full answer...

Answer 7

The etrailer Trailer Hitch Receiver #e43ZR comes with carriage bolts, fishwire, square hole spacers and flange nuts that are needed to install a receiver on your 2022 Volkswagen Tiguan that does not have the factory weld nuts and bolts. You will be…

view full answer...

Answer 8

Yes, the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13381 is a confirmed fit for all models of the 2022 Volkswagen Tiguan. It has a simple no-drill, bolt-on installation that uses the factory holes in the frame of your Tiguan.…

view full answer...

Answer 9

Yes, the Curt T-Connector Vehicle Wiring Harness item #C56403 is confirmed to fit your 2022 Tiguan R-Line. This wiring harness is custom fit and will attach behind your tail lights. It draws power directly from your VW's battery so it doesn't…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

We have a folding trailer tongue hinge that could work for the purpose you describe, as long as your trailer frame isn't constructed of aluminum. You could use the Fulton Fold Away Coupler Hinge, part #FHDPW330300. The hinge kit is designed for 3…

view full answer...

Answer 12

The best option we offer for converting a utility trailer to a recreational use trailer like one that hauls kayaks and canoes is the Malone Crossbar Conversion Kit for Standard Utility Trailer part #MPG475. It comes with brackets, hardware, and…

view full answer...