Can Just the Head of an Electric A-Frame Trailer Jack be Rotated 90 Degrees

Question

Question:

is there anyway to turn my head 90 degrees on my power hitch jack model 1817941

asked by: Tony L

0

Expert Reply:

There isn't an easy way to rotate just the head on an A-frame trailer jack such as # LC285318 or your 1817941. What you can do is rotate the entire jack and bolt it back down. This will result in a greater than 90 degree rotation but is the only way that you could turn an A-frame jack.

expert reply by: Michael H

0

Answer 1

Hello Ralph, thanks for reaching out. The etrailer Electric Trailer Jack #e23ZV will be a great option for you. The jack can be rotated to the side if needed. We have one of these jacks on our trailer here at the shop and I have seen it rotated and…

view full answer...

Answer 2

A 100 amp hour battery would suffice for powering a trailer tongue jack as well as some other accessories. For this, we have both AGM such as the Bright Way Deep Cycle RV or Marine Battery part #BRW94FR. In order to charge these batteries, you'd…

view full answer...

Answer 3

Hi Tye! The head on the etrailer Electric Trailer Jack - Drop Leg - A-Frame - 22-1/2" Lift - 3,500 lbs #e79GV is fixed, but all is not lost. Pretty much all A-Frame jacks, including this one, use a 3" on center bolt pattern. So with that…

view full answer...

Answer 4

I would recommend 10 gauge wire like our part #10-1-1 (sold by the foot) for wiring up a powered jack motor.

view full answer...

Answer 5

A wider wheel would allow the tire to have a flatter surface across the top of it when inflated which might help a little bit with tire wear but realistically that difference is very miniscule. With the Karrier ST205/75R14 Radial Trailer Tire - Load…

view full answer...

Answer 6

According to the specifications of the Electric A-Frame Tongue Jack, #LC285318, from Lippert, the jack motor can draw a maximum of 30 amps at 12 volts. The closer to the capacity of the jack (3,500 pounds) the more power it will draw. I have included…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 9

Hey Mark, the height of the etrailer Electric Trailer Jack #e23ZV that you referenced above the mounting plate is 20 inches. This is about the shortest dimension you'll get from a jack like this. Would that be enough clearance?

view full answer...

Answer 10

No worries Lorelei, I'm here to help! Very nice name by the way; I've never met a Lorelei. You probably can't say the same about my name though haha. Anyways, an electric jack is more of an upright only jack, whereas the manual options…

view full answer...

Answer 11

Hey Chris! The black wire on the etrailer Electric Trailer Jack #e23ZV is just a ground wire. Realistically you can ground it however you want but I would say running it to the frame with a self-tapping screw as indicated in the instructions is the…

view full answer...

Answer 12

Hello Jeremy, Yes, our etrailer jack #e55ZV will automatically stop and not over raise. If you check out the video that I attached you will see that Steven still has his finger pushing down the button after the jack stops. What kind of application…

view full answer...

Can Just the Head of an Electric A-Frame Trailer Jack be Rotated 90 Degrees

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching