Parts Needed to Install a Brake Controller in a 2008 Ford E-350 Van

Question

Question:

I need help with a 2008 Ford E350 15-passenger van without a tow package. I need to set-up with a 7-pin tow plug for towing a trailer with electric brakes. I have a P3 brake controller, but I need help with ing a 7-pin plug, the wire harness, and how to wire in the brake controller. Thanks.........

asked by: Wayne A

0

Expert Reply:

Your P3 # 90195 is a great controller and will work great in your 2008 Ford E-350 Van. For wiring you will need to start with a 4-way for the turn signal functions. For that you will need the part # 118551.

Next you will need the part # ETBC7 which will convert the 4-way to a 7-way and allow you to install the brake controller. This comes with everything needed to make the conversion and install the brake controller. You will want some extra wire, which you can get with part # 10-2-1.

To see how all of this will install on a van just like yours check out the video I attached. The video shows a 2006 Van which is very similar. I attached an install instruction link as well.

expert reply by: Jameson C

0

Answer 1

There are 3 options from the manufacturer for the 2009 E-350 Ford Van. Factory 7-Way trailer wiring, factory 4-Way trailer wiring, and no existing trailer wiring. I will go over all three since you did not indicate which one your vehicle has. If you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 8

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 9

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hi Charles! I completely understand wanting to avoid wiring. It can be a real pain, The good news is that the Redarc Tow Pro Liberty Brake Controller with Custom Harness #RED74CR includes a wiring harness designed to connect to the factory brake…

view full answer...

Answer 12

Hi Larry, I can definitely understand your frustration, and based on your testing, that low voltage at the 7-way is not normal and does point to an issue on the truck side rather than the trailers. Also, thank you for your photo. The good news is you…

view full answer...

Parts Needed to Install a Brake Controller in a 2008 Ford E-350 Van

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching