Recommendation for Bright, 2-1/2 Inch, Round, Trailer Tail and Clearance LED Lights

Question

Question:

I am looking for the BRIGHTEST 2.5inch LED CLEARANCE / marker lights red and amber. For trailer. Someone told me the piranhas are extremely bright. Thanks

asked by: Greg H

0

Expert Reply:

The Peterson Piranha LED 2-1/2 Inch Round Trailer Clearance Light, 3 Diode # 162R light that you referenced is certainly a bright trailer light. This 3 diode LED light will be brighter than a standard trailer light for you. I have attached a review video of the # 162R and the # 162A for you to see what the lights look like when they are on in the dark.

The Peterson Piranha lights will install on the trailer using a 2-wire pigtail and grommet, # 162-18K. These LED light will work great as replacement lights or to add lights to your trailer.

The 2-1/2 inch diameter LED lights with the most diodes are the Optronics GloLight LED Trailer Clearance or Side Marker Light, Submersible, 9 Diodes, Round # MCL157RB for red and # MCL157AB for amber. I have also attached review videos of these lights for you.

expert reply by: Victoria B

0

Answer 1

The Optronics rubber mounting ring #A45GB will fit into the hole that is 4-1/2 inches round, but the thickness of the mounting ring is 1-1/16 inches in depth. So if your plywood panel accommodates this amount of depth, then this rubber mounting ring…

view full answer...

Answer 2

We have 2-1/2 inch clearance lights but they require a 3 inch hole for the grommet like part #A55GB to install. For that you'd want the part #MCL51RB. The next size down is 2 inch but the hole required is 2-5/16 inch which wouldn't work for…

view full answer...

Answer 3

I spoke with my contact at Reese and he sent me dimensions of the Pro Series Jack, item # PS14009503676. I have included a drawing containing these dimensions for you to review. There is no owners manual included with these Jacks at this time. The…

view full answer...

Answer 4

There is not a fixed spacing for the hangers in kit #APT6SE-36 since this depends on the length of the particular springs used. The hangers need to be close enough together that the curved ends of the slipper springs properly engage with the bolt or…

view full answer...

Answer 5

If you are looking for lug nuts for the 16" Lionshead Steel Dual Wheel - 16" x 6" - 8 on 6-1/2 - 4.75" Pilot - Silver Item #LHHA420 that you referenced then you need the 5/8" Flange Wheel Nut #95188. For a standard 16"…

view full answer...

Answer 6

In order to install a brake controller on your 2007 Ford Expedition you will want to use the Adapter 4-Pole to 7-Pole and 4-Pole part #37185 as this will give you both 4 and 7 way connection points on the rear of your vehicle. The rest of the wires…

view full answer...

Answer 7

The Dexter Electric Brake Kit #23-105-106-09 is currently the only 12" brake kit we carry which utilizes the 4 bolt flange for the Kelsey Hayes axles. It was created with the 5 bolt pattern as well so that it could be used for more than just the…

view full answer...

Answer 8

Yes, you can use the seal part #RG06-070. I looked up the K71-386-00 seal that you mentioned and it has matching dimensions, an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. This seal is commonly found on Dexter axles rated…

view full answer...

Answer 9

Although the DOT numbers you gave me are codes for what testing was done on the lights, I do have a solution for you. For your 2-1/2" round clearance light we have the Peterson Piranha LED Light #162R with the wiring and grommet as part…

view full answer...

Recommendation for Bright, 2-1/2 Inch, Round, Trailer Tail and Clearance LED Lights

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching