Tips for Boat Trailer Grease Cap that Dry Rotted Quickly from Saltwater

Question

Question:

I bought these in April 2015, and they have dry rotted already. They fit perfectly. The application is on a saltwater boat trailer. Any ideas how to make them last longer? You guys rock!

asked by: David B

0

Expert Reply:

Saltwater is pretty corrosive by nature. It dry things out and causes metal to rust. Your best option would be to rinse the trailer down with fresh water as quickly as possible after removing it from the boat ramp so that you can limit the salt's exposure to the cap.

expert reply by: Jameson C

0

Answer 1

We offer rubber grease cap plugs like #DC-RP which fits a 1.18-inch dust cap hole; this is sold as a single piece. We also offer a set of two in the same size as part #RG04-010. These fit grease caps like #RG04-040.

view full answer...

Answer 2

If you are wanting to use a drill to ease operation of the winch, the Dutton-Lainson #DL11011 would be a much better choice. This winch is specifically designed so that the handle is easily removable for use with a drill. Using the shaft directly…

view full answer...

Answer 3

The 1.18" width on the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 is the only size that is offered.

view full answer...

Answer 4

The only types of winches we can recommend for hoisting like what you are wanting to do are the worm gear winches like the #DL11011 that you referenced. This winch has more than enough capacity so it would fit and work well. For a similar winch that…

view full answer...

Answer 5

The instructions for the #DL11011 state, "to minimize heat build up and possible winch damage, do not exceed 600 rpm." So, although you can use a drill with the Dutton-Lainson Drill Drive Socket Adapter for DLB Series Winches #DL6456 to…

view full answer...

Answer 6

Currently we only have the 900LB #F142007 with the strap. It is smaller than the 1,300LB #F142104 winch with a smaller handle length and drum size. As far as operating the winch they are very similar with a similar handle and switch being in the same…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Tips for Boat Trailer Grease Cap that Dry Rotted Quickly from Saltwater

Product Page this Question was Asked From

Continue Researching