Max Speed for Drill Powering Dutton-Lainson Hand Winch

Question

Question:

I have a DL11011 that I use to pull light weight carts 150lb up a ramp 12ft ramp with a 36inch rise. I want to move the carts as fast as possible. Can I use a 6,000 rpm drill to power the winch?

asked by: Jim P

0

Expert Reply:

The instructions for the # DL11011 state, "to minimize heat build up and possible winch damage, do not exceed 600 rpm." So, although you can use a drill with the Dutton-Lainson Drill Drive Socket Adapter for DLB Series Winches # DL6456 to operate your winch, you will be limited to 600 rpm.

expert reply by: Robin H

0

Answer 1

The dimensions for the Dutton-Lainson Worm Gear Hand Winch #DL11001 are as follows: Height including hand crank: 12-1/4 inches Length of side panel: 5-1/2 inches Height of side panel: 4-1/4 inches Width of base: 4-3/4 inches

view full answer...

Answer 2

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part #DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out.

view full answer...

Answer 3

The main benefit of a worm gear winch like the Dutton-Lainson Hand Winch part #DL10970 over a brake winch like the Dutton-Lainson Hand Winch part #DL74FR is that worm gear winches don't have a minimum load requirement. If you're consistently…

view full answer...

Answer 4

If you are wanting to use a drill to ease operation of the winch, the Dutton-Lainson #DL11011 would be a much better choice. This winch is specifically designed so that the handle is easily removable for use with a drill. Using the shaft directly…

view full answer...

Answer 5

The only types of winches we can recommend for hoisting like what you are wanting to do are the worm gear winches like the #DL11011 that you referenced. This winch has more than enough capacity so it would fit and work well. For a similar winch that…

view full answer...

Answer 6

The 1.18" width on the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 is the only size that is offered.

view full answer...

Answer 7

Saltwater is pretty corrosive by nature. It dry things out and causes metal to rust. Your best option would be to rinse the trailer down with fresh water as quickly as possible after removing it from the boat ramp so that you can limit the salt's…

view full answer...

Answer 8

We offer rubber grease cap plugs like #DC-RP which fits a 1.18-inch dust cap hole; this is sold as a single piece. We also offer a set of two in the same size as part #RG04-010. These fit grease caps like #RG04-040.

view full answer...

Answer 9

Currently we only have the 900LB #F142007 with the strap. It is smaller than the 1,300LB #F142104 winch with a smaller handle length and drum size. As far as operating the winch they are very similar with a similar handle and switch being in the same…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Max Speed for Drill Powering Dutton-Lainson Hand Winch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching