Powered Landing Gear Recommendation for a Loaded PJ Work Trailer

Question

Question:

Is there a electric conversion kit compatible with a pair of these pro series landing gears on my 27+5 tandem dual pj trailer that can jack it while loaded

asked by: Dave

0

Expert Reply:

There isn't a motor that can be added to the Pro Series Jacks part # PS1400960376. But if you are in the market for that style system, I recommend using # BD182804, and then add motor assembly # BD1824200100. You can also add # BDCS730300 and # BD182805.

expert reply by: Jameson C

0

Answer 1

The weight of 1600 gallons of water, without the water tank's own weight factored in, is about 13,350-lbs. For such a high-weight application I suggest Bulldog Square Jacks #BD182804 and #BD182805 along with Connecting Rod #BDCS730300. Two jacks…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hello Matt, Thanks for writing in! I'm glad you found us. We did originally have the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118784 listed as a fit for the 2025 Hyundai Santa Cruz. However, we had to remove it from our…

view full answer...

Answer 12

Hey Pete! For a hitch I recommend our own etrailer Trailer Hitch #e59ZV. This is a Class III hitch with a 2" receiver and a matte black finish. For custom wiring you can use the Curt T-Connector Vehicle Wiring Harness #C93DQ. This plugs in…

view full answer...

Powered Landing Gear Recommendation for a Loaded PJ Work Trailer

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching