Troubleshooting Bulldog Electric Landing Gear that Turns But Does Not Raise or Lower Jack
Updated 10/12/2015 | Published 10/11/2015 >
Question:
I had my bulldog electric jack professional installed and has been working perfectly. It is been used about 6 times and when I got back from camping this weekend the jack would not go up or down. The electric jack was turning and gears were moving properly but jack was stuck in the up position. Do you think I took it up too far and broke a pin.
asked by: Mike B
Expert Reply:
It sounds like you broke a bevel gear in your # BD1824200100 by over extending it and that is why everything seems to be moving but the jack does not go up or down.
When you bought this jack set it came with an extra bevel gear so as long as you still have that you can try inspecting the current one and replacing as necessary.
To access the gears inside of the heavy-duty Bulldog jacks you simply remove the screws that are holding on the plate covering the top of the jack. Once that plate is removed, the gears, pins and handle should be exposed.
We also offer the Replacement Screw and Nut Kit, # BD500217, for the heavy-duty 12,000 lb capacity Bulldog jacks. I have attached two photos that show the inner workings of the heavy-duty Bulldog jacks for you to check out.
The cross shaft that connects to the handle should be attached to the 12 toothed bevel pinion with a straight pin. You can remove the straight pin to remove the cross shaft, spring and bevel pinion. With that removed, the 18 tooth bevel gear will be exposed, and that is attached to the screw and nut assembly with a grooved pin.
Continue Researching
- Q&A: How to Remove Pin in Handle Shaft to Replace Gears on an Older Bulldog Model 12 Square Jack
- Shop: Replacement Lifting Nut for Curt Heavy Duty Direct Weld Square Jack
- Video: Comprehensive Review: Replacement Lifting Nut for Curt Heavy Duty Direct Weld Square Jack
- Search Results: trailer jack
- Shop: etrailer Square Sidewind Trailer Jack - Drop Leg - 12-3/8" Lift - 10,000 lbs
- Q&A: Trying to Get Inner Drop Leg of Bulldog Jack to Move After Getting Stuck All the Way Down
- Q&A: Installation Instructions for Bulldog Powered-Drive Kit # BD1824200100
- Q&A: What is the Purpose of the Spring Inside of a Bulldog 12K Square Jack
- Q&A: Troubleshooting A Roll Pin That Won't Slip Into Place In A Bulldog 10K Square Jack
- Q&A: Replacement Parts for Bulldog Square Jack
- Q&A: Dimensions of Bulldog Powered Jack BD500199 and Dutton Lainson DL22530
- Shop: Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 10,000 lbs
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: Review of Power Mountain Automotive Tools - Jacks and Jack Stands - PM34FR
- Search Results: trailer tires and wheels
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer wiring
- Video: Feature Review - Big Truck Big RV Trailer Jack Foot Scale with Tongue Weight Gauge
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: Suspension Enhancement
- Video: Bigfoot Hydraulic Jack DIY Installation - Diamond C Trailer
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Brake Controller

