Crown Gear Replacement Instructions for RV Slide Out
Published 09/30/2015
Question:
Iam an fairly decent mechanic . ....but.. have never replaced a crown gear on may 2008 32d fourwinds rv. Any videos or manuals available for help. Thanks you for any assistance you can give
asked by: Patrick C
Expert Reply:
I did some digging online to find instructions on how to replace the crown gear of a slide out.
First you will need to remove the retaining pin from the housing at the input shaft location and slide out shaft assembly.
Next remove retaining ring from housing at output shaft location and slide out shaft assembly.
Remove bearing retaining ring from shaft. Use bearing puller or press by applying removal force only to inner ring of the bearing or shaft.
Remove gear roll pin using pin punch with hammer or press.
Press gear onto shaft until hole in shaft and hole in gear align. Support the shaft near gear while pressing the roll pin into the gear and shaft hole. Install bearing retaining ring to shaft. Press bearing onto shaft until firmly seated on retaining ring.
Install bearing retaining ring to shaft. If gear has been removed, the bearing adjacent to the gear must be replaced. Press bearing onto shaft until firmly seated on retaining ring.
Check for noise, endplay, binding, and other indications of an incorrect assembly. If necessary remove retaining ring from output shaft and re-thrust assembly by adding or subtracting washers.
Replace grease plug.
Product Page this Question was Asked From
Replacement Crown Gear for Lippert RV Slide-Out Mechanism
- RV Slide Out Parts
- Gears
- Crown Gear
- Lippert Above-Floor Slide-Out Systems
- Lippert
more information >
Continue Researching
- Shop: Replacement Crown Gear for Lippert RV Slide-Out Mechanism
- Shop: Replacement Gear Pack for Lippert RV Slide-outs -2"x3" or 3"x3" Arms - Standard
- Video: Replacement 18:1 Venture Motor and Driveshaft with Right Angle Gear Box Feature Review
- Search Results: rv slide out parts
- Shop: Replacement 18:1 Venture Motor and Driveshaft with Right Angle Gear Box
- Shop: Lippert Roller Bearing for Above Floor Slide-Outs
- Shop: Global Link Replacement Roller for RV Slide Out - Surface Mount
- Shop: Global Link Replacement Roller for RV Slide Out - Surface Mount
- Q&A: Looking For Slide Out Gear With 24 Teeth For A 2007 Arctic Fox Slide Out
- Video: Replacement Gear Pack for Lippert RV Slide-outs -2"x3" or 3"x3" Arms Review
- Video: Let’s Check Out the Replacement Crown Gear for Lippert RV Slide-Out Mechanism
- Search Results: trailer hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Video: How to Choose a Trailer Brake Controller
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Shop: Brake Controller
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
on RV Slide Out Parts
