Will CE Smith Offset Spare Tire Carrier Fit a 2 x 2 Inch Trailer Frame and 5 on 4-1/2 Bolt Pattern

Question

Question:

will this work on a 2inch x 2inch frame? the wheel is 5 on 4 1/2.

asked by: David

0

Expert Reply:

Yes, the spare tire carrier # CE27310G can be used on trailer frames that are 2 x 2 inches. It fits frames that are 1 to 3-1/2 inches wide and up to 4 inches tall. And it is compatible with 5 on 4-1/2 bolt patterns.

expert reply by: Michael H

0

click to enlarge

Answer 1

Our trailer wheel and tire combinations like the Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 5 on 4-1/2 - LR C #AM32238B you were looking at come ready to mount, but are not balanced. Trailer tires in general are not…

view full answer...

Answer 2

I understand your concern for the accuracy of the dimensions of these products to ensure your are looking at the proper items. If you are looking at the CE Smith Offset Spare Trailer Tire Carrier #CE27310G, it fits fits 4-lug and 5-lug wheels, up to…

view full answer...

Answer 3

The speed rating "L" means that the tire is rated for 75 mph. I'm not sure the speed rating for your 8 ply tires but as long as you don't exceed the speed rating of the least rated tire you won't need to worry about that being…

view full answer...

Answer 4

The CE Smith Offset Spare Trailer Tire Carrier #CE27310G can be mounted on trailer frames which are 1" to 3-1/2" wide x up to 4" tall, so it will work for your 1-1/2" x 1-1/2" frame tube. Additionally, it can be mounted…

view full answer...

Answer 5

For a similar spare tire mount to the Fulton Economy Spare Tire Carrier #FETCSTL0701 that you referenced that works on a 3 inch trailer frame you would want the part #CE27310G. This carrier can fit on frames that are up to 3-1/2 inches by 4 inches so…

view full answer...

Answer 6

I went out to the warehouse and pulled CE Smith Offset Spare Trailer Tire Carrier #CE27310G to take some measurements. The mounting plate surface where the wheel attaches measures 3 inches wide by 6-1/8 inches tall. The overall height is 10-1/2…

view full answer...

Answer 7

It is okay to have different load range tires on each axle of a tandem axle trailer on a temporary basis but I do not recommend using the trailer in this configuration in the long term. Also, it is never a good idea to mix tires of different sizes.…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I attached…

view full answer...

Answer 10

For the weight capacity, you do not technically need a weight distribution system. However, due to the design of the trailer, I do recommend using a weight distribution system for the sway control features as the crosswinds or passing vehicles may…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Will CE Smith Offset Spare Tire Carrier Fit a 2 x 2 Inch Trailer Frame and 5 on 4-1/2 Bolt Pattern

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching