Class V Trailer Hitch Recommendation for a 2013 Ram 1500

Question

Question:

Frame mounted class 5 for 2010 ram 2500/3500 would this work on a 2013 ram 1500

asked by: Joe

0

Expert Reply:

The hitches we carry for the 2013 Ram 1500 are not also fits for a 2010 Ram 2500/3500.

So for your 2013 Ram you would want the Draw Tite Hitch part # 41948 as it is a Class V hitch confirmed to fit.

expert reply by: Jameson C

0

Answer 1

The Class II Curt Hitch #C12136 and Class II Draw-Tite Hitch #36493 for your 2016 Subaru Outback Wagon are very similar, but every Class I and Class II and some Class III Curt Hitches require stabilizing straps to be used when towing non trailer…

view full answer...

Answer 2

I recommend going with the Reese Strait-Line Weight Distribution with Sway Control System (see part numbers below). This is a dual-cam sway control system that's going to help eliminate swaying before it begins as well as helping distribute the…

view full answer...

Answer 3

The etrailer brand #e98852 and the Draw-Tite #75662 are almost identical. The capacities are the same, they'd both install in the same manner and they're very similarly priced. There are a few differences. The biggest difference is that the…

view full answer...

Answer 4

The Curt trailer hitch balls are all made in China. Many trailer hitch receivers too are made outside the U.S. but Curt does manufacture their hitches stateside. The 2-5/16-inch hitch ball you referenced, Curt #C40030, has a 15K gross trailer weight…

view full answer...

Answer 5

Curt decided not to design hitch #C13068 to account for those welded on pieces you referenced in order to maximize the size of the side hitch brackets. As to why they chose to go with a 5 bolt design I can't say. The Draw-Tite hitch #75270 sounds…

view full answer...

Answer 6

You are correct that both the Curt #C94WR and Draw-Tite #DT22MR you were looking at for your 2022 Hyundai Tuscon are very similar. Both hitches share the same 525lb tongue weight and 3,500lb trailer weight ratings, both share the same hidden…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Class V Trailer Hitch Recommendation for a 2013 Ram 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching