How to Install a Trailer Brake Controller on a 2014 Jeep Wrangler Unlimited
Updated 07/10/2015 | Published 07/08/2015
Products Featured in This Question
Question:
I cant find the port to fit the plug on my controller under my dash. Do I need another harness and where do I plug it in? 2014 Jeep Wrangler Sahara Unlimited. Pilot controller 89749 see pic Thanks
asked by: Aaron S
Expert Reply:
There isn't a port to plug in a brake controller on your 2014 Jeep Wrangler Unlimited. The controller has to be hardwired in.
If your Jeep has a factory installed 7-Way trailer connector then you need installation kit # 5506. The brake controller should have come with a universal hardwire harness, # 20127. If you do not have it then you can just cut the connector off of the end of the controller.
The brake controller black wire will go through the firewall and connect to the positive battery terminal via the 30 amp circuit breaker included with the 5506 kit. The white wire will also go through the firewall and connect to the negative battery terminal for ground.
The blue wire will get routed through the firewall, under the Jeep, and to the back of the 7-Way where it will connect to the terminal in the 7 o'clock position. Be sure to avoid areas that can pinch or melt the wire such as suspension or exhaust components for all the wires.
The red wire will connect to the cold side of the brake switch which could be difficult to reach. It is located up above the brake pedal. There will be wires going in and out of it. You need to attach the brake controller red wire to the brake switch wire that only has power when the brake pedal is pressed. To find the right wire you will need to use a circuit tester such as # 40376.
If the Jeep does not have a 7-Way but does have a 4-Way connector you will need installation kit # ETBC7 instead of 5506.
And if the Jeep does not have any trailer connector you will first install a 4-Way, # 118416, and then install the ETBC7 kit. I have included some links that will help with this installation.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Q&A: How to Install a Brake Controller on a 2014 Jeep Wrangler Unlimited
- Q&A: Brake Controller and Install Wiring Needed for 2014 Jeep Wrangler Unlimited
- Video: Best 2014 Jeep Wrangler Unlimited Trailer Wiring Options
- Shop: Vehicle Tow Bar Brake System
- Shop: Brake Controller
- Shop: Curt RVibrake 4 Portable Flat Tow Brake System - Wireless Monitor - Proportional
- Video: Install: Universal Installation Kit for Trailer Brake Controller on a 2007 Jeep Wrangler Unlimited
- Video: Best 2020 Jeep Wrangler Trailer WIring Options
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Comparing Portable Flat Tow Braking Systems - Curt RVi and Blue Ox Patriot
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Base Plate for Tow Bar
- Shop: Blue Ox Patriot Portable Flat Tow Brake System - Proportional
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Search Results: base plate for tow bar
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Vehicle Tow Bar Wiring
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Search Results: tow bar
on Trailer Brake Controller
