Replacement Hardware Recommendation for a Curt Trunnion Bar Weight Distribution System

Question

Question:

I need new bolts and washers for my 17300 with trunnion bars. I only need the heavy head bolts and tension washers that hold the head to the hitch bar. Or do I need to purchase the complete hardware kit?

asked by: Roy N

0

Expert Reply:

The only way to get the replacement Curt WD head assembly bolts would be to get the Curt Bolt kit part # C17350 that also includes several other bolts and hardware.

expert reply by: Jameson C

0

Answer 1

The parts in question are conical tooth washers. On the Curt weight distribution systems they go between the nuts and the head using the bolts that hold the head to the shank. I have included a picture that points them out for you. The tooth side…

view full answer...

Answer 2

The bar length is 30-5/8 inches long. The knuckle is 4-7/16 inches with each nipple being 1 inch tall by 1 inch diameter with a slight taper. I've attached a photo to assist. Hitch heads and spring bars are not normally compatible between brands.…

view full answer...

Answer 3

The mounting hardware for the Curt Replacement Weight Distribution Head #C17307 is found as part #C17350 on our site. This weight distribution head will fit your shank as long as the portion that it mounts to is no wider than 2" and has mounting…

view full answer...

Answer 4

Mounting hardware for the Replacement Head for Curt TruTrack Weight Distribution System w/ Sway Control #C17506 is not included. Since it's a replacement part you'd want to reuse the hardware that came from the old head.

view full answer...

Answer 5

Yes the Curt weight distribution head part #C17307 is compatible with the shank part #EQ90-02-4600 that you also referenced. These two parts together would give you a really long ball mount setup with an adjustable height. You'd also need the…

view full answer...

Answer 6

In terms of compatibility, it depends on which components of a weight distribution system you are referring to. For example, Curt spring bars will not fit in a Reese head nor will Reese bars fit in a Curt head. But, if you are talking about the…

view full answer...

Answer 7

The Curt Bolt Kit for Trunnion Style Weight Distribution Hitch, #C17350, will be the hardware kit that you will need for the Curt Replacement Weight Distribution Head for Trunnion Style Bars, #C17307.

view full answer...

Answer 8

I do have an option for you but the Curt Bolt Kit for Trunnion Style Weight Distribution Hitch part #C17350 does not come with the spring bar retainer clips that you are referring to. Unfortunately, these retainers clips are not sold separately as…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Hardware Recommendation for a Curt Trunnion Bar Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching