2nd Motorhome Kit Recommendation for Vehicle Bought with Invisibrake System

Question

Question:

I purchased a 2013 Jeep Wrangler with a complete Invisabrake system already installed. I need the wiring package to allow me to hook up use the Invisabrake system.

asked by: Bruce F

0

Expert Reply:

The correct kit you would need to use the Invisibrake part # RM-8700 you have installed on your 2013 Jeep Wrangler would be the 2nd Motorhome Kit part # RM-98850.

expert reply by: Jameson C

0

Answer 1

You'll need to test to see if there is power getting to the LED light, and for that you'd test the red power wire using Cordless Circuit Tester #PTW2979. Removing it from the dash just depends on how you got it in, but generally it is drilled…

view full answer...

Answer 2

We don't have an installation video specific to the Roadmaster Replacement LED Display Monitor #RM-300065-00 but I have attached a video below of us installing the entire Roadmaster InvisiBrake System #RM-8700. You can skip ahead to around the…

view full answer...

Answer 3

The LED Display Monitor for BrakeMaster Systems #RM-300065-00 should light up each time you brake with your motorhome as the Roadmaster InvisiBrake Supplemental Braking System #RM-8700 is supposed to activate when the brake lights on your RV are…

view full answer...

Answer 4

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 5

The motorhome monitor alarm in Monitor/Alarm Kit #RM-98850 will not sound when you press the motorhome brake pedal. If someone presses the toad brake pedal for more than 20-seconds then you should hear the alarm. As for the breakaway my contact at…

view full answer...

Answer 6

It may just be that the LED indicator on the brake controller is out. You will want to ensure proper controller function though by using a circuit tester such as #PTW2993. You will want to sever the blue wire a few inches back from the controller and…

view full answer...

Answer 7

The installation instructions for Roadmaster second RV kit #RM-98850 are pretty straight forward. You would not tap into the blue wire because on a 7-Way blue is usually for electric brakes. If tapped into the blue wire the light would not work…

view full answer...

Answer 8

There isn't a guide out there that will tell us where the port is located but it generally is right under the dash near the steering column. I've attached a picture of a 2017 Pace Arrow where we were provided with a picture of where it was…

view full answer...

Answer 9

It does sound like they did not install the Braking Monitor/Alarm Kit #RM-98850 correctly for the Roadmaster InvisiBrake #RM-8700. That or whomever installed the entire kit on your Jeep the first time switched something around on both the motorhome…

view full answer...

Answer 10

The long and short of it is that you need to route wiring from the cold side of the stop light switch (only gets hot when brake pedal is pressed) on your dinghy up to the location that you are mounting the RoadMaster Replacement LED Display Monitor…

view full answer...

Answer 11

The brake controller plug will be located behind the dash in one of two places, as you can see in the photos I've provided. Most likely, the connector will be located behind a panel on the right side of the dash, as shown in the first set of…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

2nd Motorhome Kit Recommendation for Vehicle Bought with Invisibrake System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching