Possible Quick Connect Recommendation for a 12k Badlands Winch

Question

Question:

I want to put a quick connect on my 2003 Dodge 3500 for my winch. I have a 12000 lb bad lands winch what connects an size wire should i use??

asked by: William M

0

Expert Reply:

The Trailer and Vehicle Electric Winch Wiring Kit # BDW20207 on your Badlands 12,000 winch will work well.

The 2 AWG wire will be adequate for your winch as it is confirmed to work on Superwinch winches up to 16.5k in capacity.

expert reply by: Jameson C

0

Answer 1

The Bulldog Winch Receiver Mount Kit #BDW20155 has the standard 10 x 4.5" mounting bolt pattern which will match up exactly with your Badland Apex 12000. As for the wiring, you will need to route the wire from your 4Runner battery and mount the…

view full answer...

Answer 2

Ideally, you'll want some of the hardware attaching the e-track to the trailer floor to also secure to the cross members as well as to the planks that make up the trailer floor. If that's not possible, I'd recommend using a backer plate…

view full answer...

Answer 3

For an Anbull 13000-lb winch, I recommend going with a 2 gauge wire like the Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End, part #BDW20207. It can handle any winch up to a 16.5K capacity. It is 24 feet long, which is the longest we…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Hey Paul! Wiring like the Curt #C96JR is plug and play which makes for a pretty simple installation. However, it isn't the most reliable, and you won't be able to add a charge line without swapping out the connector on the end. When…

view full answer...

Answer 10

Hey Fred, welcome back. There is no flat towing wiring harness with built in diodes that doesn't require splicing into your Gladiator's lights. You will definitely need the diodes regardless of what flat tow braking system you're using.…

view full answer...

Answer 11

Hey Lee, that's a great question but it doesn't matter where the lighting kit part #RM47ZR wires in relation to the trailer wiring. As long as both are installed on the right circuits everything will work great together. Do you think…

view full answer...

Answer 12

There are a couple of pretty big differences between the Draw-Tite Trailer Hitch Receiver #DR64FR and the Curt Trailer Hitch Receiver #CU74FR that fit your 2021 Jeep Gladiator, and I'll go over them so you can decide which trailer hitch is the…

view full answer...

Possible Quick Connect Recommendation for a 12k Badlands Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching