Rear Sway Bar Recommendation for a Workhorse W22 Workhorse Winnebago Adventurer

Question

Question:

I have a 2007 Workhorse W22 chassis under my Winnebago adventurer. Will i be required to drill the frame for this application? Thanks for your help,

asked by: Terry K

1

Helpful Expert Reply:

Actually for your W22 chassis RV the correct rear sway bar would be the # RM-1259-109 for if you are 33 feet or longer or part # RM-1259-108 for if you are shorter than that.

There will be some drilling required for installation. I attached instructions for both products for you to check out as well.

expert reply by: Jameson C

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Hi Todd, I know exactly the feeling you’re describing, and you’re definitely not alone. That floaty, pushy feeling at highway speeds, especially when trucks pass, is really common on the Sprinter 3500 chassis with a taller coach like your Tiburon,…

view full answer...

Answer 5

The Roadmaster Rear Anti-Sway Bar for Motorhomes #RM-1139-143 can use your factory u-bolts if they are long enough. If they are not, then Roadmaster recommends using the 7/8 inch diameter u-bolts that are longer (most likely the larger diameter due…

view full answer...

Answer 6

You're already on the right track with everything you looked at. Your 2018 Thor ACE 30.3 has a GVWR of 18,000 lbs so I recommend the following: -Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes #RM33RR…

view full answer...

Answer 7

I am not sure what is wrong with the links but I have included a picture of the instructions for the rear, #RM-4139-125, and for the front, #RM-4139-127, for your RV built on the 1997 Ford F-53. V8 chassis. The rear is on the top and the front is on…

view full answer...

Answer 8

For your 2021 Thor challenger 37FH sitting on a 2020 F 53 chassis with a GVWR of 24k the front SumoSpring kit you'd want is the part #SSF-173-40-2 and then for the rear #SSR-183-54-1.

view full answer...

Answer 9

Hi Bob; since there is less stability at the rear of your 2013 Thor ACE 30.1 the rear anti-sway bar will have the greatest impact. The correct part for your motorhome is the Roadmaster Rear Anti-Sway Bar #RM-1139-146. It sounds like you plan on…

view full answer...

Answer 10

For the front anti-sway bar on your 2018 Forest River FR3 30DS with an F-53 chassis you need the Roadmaster part #RM-1139-148. The rear anti-sway bar is the Roadmaster part #RM-1139-149. You do need to check to ensure there is enough factory u-bolt…

view full answer...

Answer 11

I was able to reach out to my tech contact over at TorkLift to get some guidance on the installation of the TorkLift Front Tie-Down #TLF2022 for you. He mentioned that you'll want to apply pressure to the tie-down (pull it down a little bit) or…

view full answer...

Rear Sway Bar Recommendation for a Workhorse W22 Workhorse Winnebago Adventurer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching