Grease Seal Recommendation for a Trailer Hub with L68149/L44649 Bearings

Question

Question:

Hi, Could you assist me in selecting the correct grease seal? My bearings have the following numbers stamped on the top. L68149 Inner L44649 outer

asked by: Phil H

0

Expert Reply:

Based on your bearing numbers the correct grease seal set you would need would be the Grease Seals part # RG06-050.

expert reply by: Jameson C

0

Answer 1

The correct hub and drum assembly replacement for your Lippert 4,400 lb axle is the #8-407-5UC3-EZ. This comes with bearings and a grease seal. If you need brakes as well you can use the #LC66WD, or for self-adjusting brakes #K23-478-479.

view full answer...

Answer 2

The Lippert Electric Trailer Brake Kit #LC66WD contains the Left #LC96WD and Right #LC46WD hand brake assemblies for a Lippert 4,400lb axle. We do not carry just the replacement shoes and springs for your axle.

view full answer...

Answer 3

Dennis, many times Dexter hubs will fit on a Lippert axle, but Lippert does have a few axles out there with special spindle sizes. For your Lippert 4,400 lb axle, you can use the Trailer Hub and Drum Assembly #AKHD-655-35-K. Your 4,400 lb axle does…

view full answer...

Answer 4

The correct hubs for the 4400 Lb Lippert Axle NV178936 are 3,500 lb hubs as confirmed by Lippert. If you need to replace the hubs, I recommend Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased part…

view full answer...

Answer 5

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Grease Seal Recommendation for a Trailer Hub with L68149/L44649 Bearings

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching