Toolbox Tray Recommendation for a 20 inch Wide Toolbox

Question

Question:

do you have a 20 in wide truck toolbox tray

asked by: Carlos T

0

Expert Reply:

If you have a Deezee 20 inch wide red label toolbox we have a tool box tray that would work for you. For that you would want the part # DZTBTRAY1. This measures 18" x 15-1/2".

expert reply by: Jameson C

0

Answer 1

The brake controller install port on your 2017 GMC Sierra for installing your Primus IQ part #TK90160 is located under the dash under the junction box lid you see in the picture I attached. I also attached an install video below that details how this…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Dennis, thanks for reaching out! We have yet to install the Towsmart Trailer Hitch Receiver #TS34ZR, but it has a similar design to the Curt #C69VV, which we had a chance to install on a 2024 Outback Wagon. This will be the same as your 2025…

view full answer...

Answer 8

Hey Joe, yes the Draw-Tite Max-Frame Trailer Hitch Receiver #DT73RR will fit your 2025 Subaru Outback. But, if you're open to another option, the Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT74YR is what I'd go for. This hitch is a bit…

view full answer...

Answer 9

We definitely have some trailer jacks you can use as a replacement for your Dutton-Lainson but it doesn't look like anything we have will work as a direct replacement. If you'd like to stick with the Dutton-Lainson brand then I recommend…

view full answer...

Answer 10

I walked out to our warehouse and pulled the UWS Plastic Tray, #UWSPTRAYS, from our inventory. I measured the tray and added dimensions to a picture for you. Check out the attached picture. The tray measures 19-3/8 inches by 18-5/8 inches. There are…

view full answer...

Answer 11

The overall dimensions of the UWS Aluminum Tool Tray #UWS060059 are 26-1/2" Wide, 16" long, and 1-1/2" deep including the lip. The INSIDE dimensions for interior storage are 24-1/2" Wide, 16" long, and 1-1/2" deep. I…

view full answer...

Answer 12

The Replacement Black UWS Logo Badge #UWS99FR normally installs with rivets or nuts and bolts. I am sure there is a way you could use an adhesive to install it but it's hard to say exactly what would be the best route for that.

view full answer...

Toolbox Tray Recommendation for a 20 inch Wide Toolbox

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching