Where to Get the Stoplight Circuit on a 2015 GMC Terrain for Brake Controller Install

Question

Question:

Is it the number 11 white wire on the b cm on the 2015 gmc terrain the cold side of the brake switch to wire the electric brakes

asked by: Dennis D

0

Expert Reply:

Yes, it should be the number 11 position of the BCM you have on your 2015 GMC Terrain for the stoplight switch of the vehicle for brake controller installation.

I attached a picture that shows a diagram for the BCM with the correct pin pointed out.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You are correct that your tail and brake lights are on one circuit. Your vehicle has combined wiring, and all of the wires run to a single socket in the tail light housing. The Hopkins Wiring Kit #HM56108 connects behind the tail lights of your 2013…

view full answer...

Answer 2

The BCM connector wire colors on your 2015 GMC Terrain could vary during production. I recommend using a circuit tester such as #PTW2993 on the wire in the number 11 terminal to determine its function. I included a diagram for you to view. Another…

view full answer...

Answer 3

According to the online manual for the 2015 GMC terrain that I looked at the vehicle can be flat-towed once a few steps are taken, including the removal of fuse 32 that's in the interior fuse box to prevent battery drain. I suggest you refer to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Where to Get the Stoplight Circuit on a 2015 GMC Terrain for Brake Controller Install

Continue Researching