Width of the Camco RV Vinyl Trim Insert # CAM25202

Question

Question:

Camco RV Vinyl Trim Insert - White - 100foot Long x 1inch Wide Just attempting to verify how this product is specd. Does the 1inch dimension refer to the installed width of the trim or to the dimensions of the rail that the product is ed into ? Thanks in advance !

asked by: Stephen M

0

Expert Reply:

I went out to our warehouse to measure the width of the Camco RV Vinyl Trim Insert # CAM25202 that you referenced and found that it is 1 inch thick.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Camco RV Vinyl Trim Insert #CAM25202 that you referenced has an overall width of 1 inch. That's the size of rail it would fit into. I attached a picture that shows it's width for you to see as well.

view full answer...

Answer 2

Frank, by far it's going to be the Camco RV Vinyl Trim Insert #CAM25202. Both trims are made of Vinyl, but the Camco #CAM25202 also has UV inhibitors as well which is going to provide some long-lasting protection against the sun.

view full answer...

Answer 3

The only difference between the Valterra Universal Barbed Drain Valve #A01-2025VP and the Camco RV Drain Valve - Barbed #CAM22223 is the manufacturer. Apart from that, these are the same drain valves that each have 1/2" and 3/8" diameter…

view full answer...

Answer 4

The Camco RV Drain Valve w Flange for 1/2" or 3/8" Diameter Drain Hose - Barb Thread #CAM22223 has a flange measurement is 1 7/8 inch diameter and the measurement of the holes center on center is 1 7/16 inches.

view full answer...

Answer 5

The best way to select the correct size vinyl trim insert is to measure the trim insert you have now while flat, not the track. We don't really recommend measuring the track as they are not all a standard width. That said, we only offer vinyl…

view full answer...

Answer 6

For your parts list, I have a couple recommendations: 1. We only have a couple of refrigerator vents/access doors and unfortunately not anything that is compatible with your measurements. The cover does need to have venting in some capacity. I've…

view full answer...

Answer 7

There are going to be two options for best caulk or sealant for your RV and it is going to depend on where your are using it. If you are on your roof you will want a self leveling sealant like the Alpha Systems 1021 Self-Leveling Sealant for RVs -…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Width of the Camco RV Vinyl Trim Insert # CAM25202

Product Page this Question was Asked From

Continue Researching