6k Rated Agricultural Hub and Spindle with 6 Lug Bolt Pattern

Question

Question:

I am needing a spindle and hub setup for some ag trailers were building. I need a 6 lug 3k per side with a solid type wheel. What do you recommend?

asked by: Robert H

0

Expert Reply:

For an agriculture hub designed for a 6k axle with a 6 on 6 inch bolt pattern you would want the part # 42660UC1.

For the matching spindle for this hub you would want the number 42 spindle part # TRU57FR.

expert reply by: Jameson C

0

Answer 1

Agricultural hubs, such as the Dexter #42660UC1, are designed specifically to fit agricultural applications and certain spindle models. These types of hubs are typically used in building or repairing implement wagons, carts or machinery. The spindles…

view full answer...

Answer 2

Hey Ethan, while I don't know exactly what info you are looking for I can tell you that the #42 spindle you have referenced part #TRU37FR is correct for a 5,200 lb axle. Then for a hub/drum you'd want the part #AKHD-655-6-K. Are you in need…

view full answer...

Answer 3

Hey Steve, the #84 Spindle for 3,500-lb Trailer Axles #TRU64FR is not going to work with the Dexter Trailer Idler Hub Assembly for 6,000-lb Axles #42660UC1. You'd actually want to use either the #42 Spindle for 5,200-lb to 7,000-lb Trailer Axles…

view full answer...

Answer 4

Based on the bearing sizes #25580 and #LM67048, there are two possible hubs that will fit. The first has a wheel bolt pattern of 6 on 5-1/2 and fits axles rated for 5,200 lbs to 6,000 lbs. This hub can be purchased with the standard hub assembly…

view full answer...

Answer 5

Although the outer bearing of the #AKIHUB-655-6-K hub assembly will fit, the inner bearing will be too large. Instead, you'll need the Complete Agricultural Hub Assembly, #AH30660FCOMP, which is designed to fit the agricultural spindle #TRU34FR.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

6k Rated Agricultural Hub and Spindle with 6 Lug Bolt Pattern

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching