Instructions and Parts Needed to Install Brake Controller on 2011 Chevrolet Silverado 1500

Question

Question:

I want to install a factory style in the dash brake controller on my 2011 chevy 1500. How can I use the trucks existing components to do this? And do you carry the parts?

asked by: Floyd O

1

Helpful Expert Reply:

When it comes to a brake controller the Tekonsha Prodigy P3, # 90195, is a top performer and a customer favorite. This proportional brake controller activates the trailer brakes in proportion to the Silverado's braking action and automatically adjusts trailer's braking based on deceleration of tow vehicle. The P3 activates immediately so there is no pausing like with a time-delayed brake controller. This style is typically mounted right up under the dash.

Since your 2011 Chevrolet Silverado is already equipped with a 7-way connector, the only parts needed will be the brake controller. I have attached an article which gives step by step installation instructions as well as an installation video which are a tremendous help when it comes time to complete the install.

We do not offer any factory style, in the dash, brake controllers.

expert reply by: Leah S

1

Answer 1

I sent you a separate email with the instructions for installing the EcoHitch Hidden Trailer Hitch Receiver #EH55VR on your 2023 Mazda CX-30. I do recommend installing the 4-Way #C86CR when you install the receiver. The instructions for this are…

view full answer...

Answer 2

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Instructions and Parts Needed to Install Brake Controller on 2011 Chevrolet Silverado 1500

Featured Help Information

Miscellaneous Media

Continue Researching