Will Snap-on Reflector Ring # A78RXB Fit Optronics GLOLight LED Stop/Turn/Tail Light # STL178RFPB

Question

Question:

Hi. Will your Optronics A78RXB snap-on reflector fit the STL178 series?

asked by: Shawn M

0

Expert Reply:

Although the Snap-on Reflector Ring, # A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light # STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and Tail Light, # STL78RB. This light was designed to be used with the reflector ring.

I spoke with my contact at Optronics and they do not offer a reflector ring for the STL178 series lights.

expert reply by: Leah S

0

Answer 1

The proper hardwire wiring harness for the #STL178RFPB GloLight LED trailer tail light is the #A47PB. A great and similar style side marker/clearance and turn light is the #STL78AB, this will already have the proper wires to install on your trailer.…

view full answer...

Answer 2

The GloLight LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 22 Diodes - Oval - Red Lens #STL178RFPB is most likely a fit for your 2018 Coachmen Clipper ST108. The best way to confirm fit is to check the mounting hole locations. The…

view full answer...

Answer 3

The #A78RXB snap on reflector ring you mentioned is only compatible with Optronics STL78 series taillights like the #STL78RB , none of which has the provision for a reverse lamp. Your best bet would be to use a #STL78RB stop/turn/taillight and a…

view full answer...

Answer 4

I believe the tail lights you have are the TecNiq T60 lights which are industry standard 6" oval recessed lights. To replace those you can use the Optronics Fleet LED Trailer Tail Lights #TLL12RK. If your lights look different than this please…

view full answer...

Answer 5

The Foam Gasket #A32GB is for your LED Clearance or Side Marker Trailer Light in Amber #MCL0032ABB or Red #MCL0032RBB.

view full answer...

Answer 6

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 7

I do have a solution that should work for you, but we do not carry any Optronics lights with the style connector you have. You could get a Optronics Trailer Light #STL78RB that you referenced, and to install it you would just want to cut of the…

view full answer...

Answer 8

Thank you for your purchase from etrailer.com! The Optronics Sealed, 6-1/2 Inch Oval LED Trailer Stop, Turn, and Taillight #STL78RB that you purchased will need to be hardwire installed on your trailer. You will want to connect the light to your…

view full answer...

Answer 9

No, I am sorry Randy there is not. The Optronics LED Trailer Tail Light item #STL78RB has a built in flange but we do not have a gasket for it.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Will Snap-on Reflector Ring # A78RXB Fit Optronics GLOLight LED Stop/Turn/Tail Light # STL178RFPB

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching