GloLight LED Tail Light Compatibility with 2018 Coachmen Clipper ST108
Published 05/14/2019
Products Featured in This Question
Question:
Thanks for the quick response. The holes for the STL178RFPB line up properly. I have a follow-up question. On the web page for the tail light, I saw a pig-nose connector (3 prong) coming out from the assembly. When i disassembled the tail light on my trailer, I saw that there are 3 wires running from the current tail light assembly to connectors inside the trailer. I have attached 2 pictures for your review. Would I have to cut the wires on the STL178RFPB tail light to make it work ? That makes me a little nervous. Thanks for the help
asked by: David L
Expert Reply:
The GloLight LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 22 Diodes - Oval - Red Lens # STL178RFPB is most likely a fit for your 2018 Coachmen Clipper ST108. The best way to confirm fit is to check the mounting hole locations. The mounting holes are 7 inches on center and 2-11/16 inches on center. I've attached a photo to assist.
Then you can use the Snap-on Reflector Ring for STL78RB Series LED Lights - Red # A78RXB or the chrome ring # A78CB.
Product Page this Question was Asked From
GloLight Halo LED Trailer Light w/ Flange - Brake, Tail, Turn - Submersible - Oval - Red
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- Oval
- Surface Mount
- Submersible Lights
- LED Light
- 7-1/2L x 3-5/16W Inch
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Shop: Optronics LED Trailer Light w/ Flange - Brake, Turn, Tail - Submersible - Surface Mount - Oval - Red
- Video: Optronics LED Trailer Tail Light: The Breakdown
- Video: Review of the Snap-on Reflector Ring for Flange or Surface Mount Trailer Lights
- Video: What to Know About the Reflex Reflector Flange Cover for Optronics 6" Oval Trailer Lights
- Shop: Snap-on Reflector Ring for Flange or Surface Mount Trailer Lights - Red
- Shop: GloLight Halo LED Trailer Light w/ Flange - Brake, Tail, Turn - Submersible - Oval - Red
- Shop: Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diode - Oval - Red Lens
- Shop: Reflex Reflector Flange Cover for Optronics 6" Oval Trailer Lights - Snap-on - Qty 1
- Shop: Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diode - Oval - Clear Lens
- Search Results: dw05744
- Search Results: amber side marker
- Search Results: peterson grommet
- Search Results: trailer lights
- Video: Let’s Check Out the GloLight LED Trailer Tail Light
- Article: Most Popular Wheel Bearings
- Video: Let’s Check Out the 3-Wire Pigtail for Optronics Trailer Lights
- Video: Complete Breakdown of the Sealed, 6-1/2" Mid-Ship Turn Signal and Side Marker Light
- Video: A Closer Look at the Right Angle 3-Wire Pigtail for Optronics Trailer Lights
- Search Results: clearance lights trailer lights
- Search Results: side marker
- Search Results: marker light
- Q&A: Which Wiring Harness Will Be Needed to Install the Optronics GloLight LED Trailer Light STL178RFPB
- Q&A: Determining Which Taillights Fit Skeeter Boat Trailer
- Q&A: LED Lights for 1991 Ranger Boat Trailer
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Minivan Model for Flat Towing Behind Motorhome
- Q&A: Replacement Anode Rod for a Suburban 6-Gallon Hot Water Heater
- Q&A: Trailer Light Replacement Lens for Light Marked SAE-A-P2-DOT-02
- Q&A: Trailer Tail Light Replacement Recommendation for TecNiq 16P2S2T2T60
on Trailer Lights
David
5/14/2019
Thanks for the quick response. The holes for the STL178RFPB line up properly. I have a follow-up question. On the web page for the tail light, I saw a pig-nose connector (3 prong) coming out from the assembly. When i disassembled the tail light on my trailer, I saw that there are 3 wires running from the current tail light assembly to connectors inside the trailer. I have attached 2 pictures for your review. Would I have to cut the wires on the STL178RFPB tail light to make it work ? That makes me a little nervous. Thanks for the help