Valve Stem Hole Diameter for Dexstar Steel Mini Mod Trailer Wheel - 15 x 6 Rim - 5 on 4-1/2

Question

Question:

what size is the valve stem hole?

asked by: Dennis W

0

Expert Reply:

The valve stem hole for Dexstar wheel # AM20551 is 0.45 inches in diameter. The wheel is rated for 2,050 pounds at 75 psi so valve stem # AM20904 would fit. It is rated up to 80 psi.

expert reply by: Michael H

0

Answer 1

Both the Dexstar Steel Spoke Trailer Wheel #AM20352 and the Dexstar Steel Mini Mod Trailer Wheel #AM20365 that you referenced are made of the same material and have the same powdercoat finish so either would be just as great as the other when being…

view full answer...

Answer 2

The Kenda Loadstar ST175/80D13 Bias Trailer Tire #AM3S120 that you referenced is going to close that trailer frame to tire gap by almost a full inch. This would put the new tire much too close to the frame on your Harbor Freight Trailer. The issue is…

view full answer...

Answer 3

The Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range B #AM30590 have a max speed of 65 mph. When trailer tires are not speed rated with a letter, the default is 65 mph max. I've attached an article to…

view full answer...

Answer 4

Yes, you can change from a 4.50-12 to a 4.80-12 trailer tire like the Kenda K353 Bias Trailer Tire - 4.80-12 - Load Range C #AM10062. I was unable to find the rim size a 4.5-12 tire uses, but a 4.80-12 tire fits 12" x 4" rims, so if…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Valve Stem Hole Diameter for Dexstar Steel Mini Mod Trailer Wheel - 15 x 6 Rim - 5 on 4-1/2

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching