Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs

See what our Experts say about this CURT Trailer Hitch Ball Mount

• Ball Mount for 2007 Mercury Grand Marquis Towing U-Haul Trailer
  Hi Ryan; the Curt Class II Drawbar # C45015 is the better choice here. Since your measurement is 12" you need a 6" rise for the U-Haul trailer. It doesn't have to be 100% perfect, and rarely is, so the 5" rise from the Curt ball mount is your best option. This has a 3/4" ball hole diameter so you can use the # C40018 for a 2" ball.
  view full answer...
• Curt Ball Mount for 1-1/4 inch Hitch with More Rise and Length than C45520
  The two Curt ball mounts you mentioned of part # C45014 and # C45015 are both options that would give you additional rise with the # C45015 being a few inches longer as well than compared to the # C45520 that you have now. Now these options only can be used on Class II hitches whereas the # C45520 can fit Class I or Class II so you'd need to verify that with the hitch of your vehicle. The reason for this is that the Class I hitches are lower in capacity so they can be only used with the...
  view full answer...
• Trailer Hitch Ball Recommendation for Curt Ball Mounts C45015 and C45014
  For a 1-7/8 inch hitch ball to use with the # C45015 or the # C45014 you would want the part # A-80. For a 2 inch hitch ball you would want the part # A-82. Both of these have a 3/4 inch diameter shank that is 2-1/8 inch long.
  view full answer...
• Ball Mount Recommendation to Clear the Back of a 2007 Chevy HHR
  If you were to use ball mount # C45014 on your 2007 Chevy HHR it would be very tight so I do recommend going with the longer # C45015. If you have or are looking at hitch # C11447 then the ball mount that Curt recommends is # C45520 which is about the same length as C45015 so it would also have enough length. For either ball mount if the trailer takes a 2 inch ball use # C40018. And if it takes a 1-7/8 inch ball use # C40001. And if you don't already have a trailer wiring harness you can...
  view full answer...
• How to Find Rise/Drop of Ball Mount Needed for Towing Small Aluminum Boat with 2007 Acura TL
  When we installed the Draw-Tite # 24755 Class I hitch on a 2007 Acura TL, we found that the inside top edge of the receiver tube sat 10-1/2 inches above the pavement. To determine which ball mount would place your trailer as close to level as possible, you'll need to put the boat trailer up on it's jack so it's level, then measure from the bottom edge of the coupler to the ground. The height difference between 10-1/2 inches and the level trailer coupler height equals the amount of rise/drop...
  view full answer...
• Ball Mount Compatibility with Class I Trailer Hitch Receiver on 2010 Ford Mustang
  The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11048 is compatible with the Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs # C45015 you referenced. You will also need a hitch ball like # 19256 for a 1-7/8 inch diameter or # A-82 for a 2 inch diameter. For trailer wiring, I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118487. This will connect behind your tail lights and then draw power directly from your battery....
  view full answer...
• Ball Mount For a 2013 Chevy Camaro with 1-1/4 Hitch
  You are probably OK but if you are anything like I am it would be too close for comfort. I wouldn't want to take a chance at potentially causing any damage to my fascia. I recommend the Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs Item # C45015. The hitch on your vehicle is 8-1/2 inches from the center of the hitch pin hole to the outer most part of your fascia and 9-3/4 from the ground to the top inner most part of the receiver tube. This ball mount has an 11-5/8" long shank...
  view full answer...
• Recommended Drawbar for Volvo 2001 V70 XC
  Width usually isn't a consideration when it comes to choosing a drawbar. Folks are typically concerned about getting a drawbar that places the trailer ball at the proper height so the trailer is level when it's being towed. I'll link you to our FAQ article about ball mounts/drawbars. If by width, you're speaking of the hitch receiver size the drawbar is meat to fit into, the hitches we offer for the 2001 Volvo V70 are Class II, which use the 1-1/4 by 1-1/4 receiver (inside dimension of...
  view full answer...
• Curt Class II Euro Style Drawbar # C45592
  After speaking to my contact at Curt, I found the most height extension you can achieve with the Curt Class II Euro Style Drawbar # C45592 for your 2011 Volkswagen Golf is with the Curt Class II Drawbar # C45015. This is a 5-1/8 inch rise drawbar which provides a total height increase of 2 inches for any cargo you would tow with your vehicle.
  view full answer...
• Will Curt Drawbar Clear Bumper On 2004 Chrysler Town And Country
  There is an easy way to make sure you clear the bumper on your 2004 Chrysler Town and Country. You will need a tape measure and a straight edge like a yardstick or a dowel. Hold the straight edge vertically against the rear bumper, making sure it extends below the hitch opening. Then just measure from the center of the hitch pin hole to the straight edge. This gives you the distance you need to clear the bumper. The Curt Class Drawbar, part # C45014, measures 9-5/8 inches from the center...
  view full answer...
• Custom Trailer Hitch Adapter For Chevrolet Malibu from 1-1/4 hitch to 2 Receiver
  My recommendation is to have a custom adapter made for the height and length that you need on your 2010 Chevrolet Malibu with the Draw-Tite Trailer Hitch Receiver # 36479. The center of the hitch pin is about 8-1/2" from your rear bumper. Any adapter that goes from a 1-1/4" receiver to a 2" receiver will reduce the weight capacity of the vehicles receiver by 50%. Be sure to verify your vehicle and hitch ratings to determine if you will have enough capacity for what you intend to haul. The...
  view full answer...
• Upgrading to Class III Hitch for Towing 3000 lb Boat with 1997 Chevy S-10
  You can see the various hitches available for your vehicle by clicking on the provided link. Use the drop down menu to choose the bumper style of your S-10. The Class II hitch for a 1997 S-10 has a 3500 lb towing/300 lb tongue weight capacity, while the Class III has a 3500 lb towing/350 lb tongue weight capacity. You can certainly change to a Class III if you wish, but you will only realize a 50 lb increase in tongue weight. I would recommend you determine the fully loaded and ready...
  view full answer...
• Roof Rack Options for Loading 2 Kayaks onto a 2018 Honda Civic 4dr
  The first thing to look at is the roof capacity of your vehicle. The combined weight of the rack, 2 kayak carriers, and a pair of 64 pound kayaks is a concern. I confirmed the roof capacity is 110 pounds on the 2018 Civic Sedan. A better option and my recommendation is carrying your 2 kayaks on a Malone MicroSport Trailer designed for 2 Kayaks # MPG461G2. If you don't already have a tow package or hitch on your Civic, it requires a tow hitch like the Curt Trailer Hitch Receiver #...
  view full answer...
• Will Curt Trailer Hitch Fit 2011 Audi A3 TDI S-Line
  I went ahead and verified with the manufacturer for you that the Curt hitch will indeed fit your 2011 Audi A3 TDI S-Line with the Sport package; the correct part number for the hitch is the following: - Curt Trailer Hitch Receiver # C11192 The Curt # C11192 will fit your Audi and is nice because the crosstube is entirely concealed so that the only thing showing is the receiver, helping your A3 keep its factory appearance. If you plan on using this for just an accessory like a bike rack,...
  view full answer...
• Can I Haul A Trailer With 2 Motorcycles With My 2012 BMW Series I With Class I Hitch?
  On your 2012 BMW Series 1 your only option is the Curt Class I 1-1/4 inch hitch # C11184 which has a max tongue weight of 200lbs and a max gross trailer rating of 2,000 lbs. So, you could potentially haul your two motorcycles on your trailer but there are some things we need to make sure of. First make sure that your vehicle can handle that weight. The hitch may be able to, but you need to confirm your vehicles limits. Usually you'll find it in your owners manual. Then we need to make...
  view full answer...
• Does Curt Ball Mount # C45015 Have Clearance with Curt Hitch 2012 Chrysler Town and Country
  From the center of the hitch pin hole of the Curt ball mount part # C45015 to the back of the ball mount platform measures 8 inches. This would easily have enough clearance with the Curt hitch part # C12264 you have installed on your 2012 Chrysler Town and Country.
  view full answer...
• Long Ball Mount for Class II Trailer Hitch Receiver on a 2006 Jeep Grand Cherokee
  The longest ball mount we carry to fit a Class II, 1-1/4 inch hitch receiver is the Curt # C45000. It's 13-1/2 inches from the hitch pin hole to the ball hole. However, it only provides 3-7/8 inches of rise and cannot be used in the drop position. Much less than the Brophy # BM96 you have. It does have the same 3/4 inch ball hole diameter as the Brophy. Another option that may work is the Curt # C45015 that's 11-5/8 inches long. It can't be used in the drop position either but does...
  view full answer...
• Hitch Lock and Anti-Rattle Device Recommendation for Curt Ball Mount # C45015
  Since the shank of the ball mount part # C45015 is solid you'd have to go with a standard hitch lock like the part # TR63254 which will work well. Then for an anti-rattle device you'd want a universal kit like the part # RM-061-125.
  view full answer...
• Is the Material of Curt Class II 1-1/4 Inch Hitch # C45015, Solid Steel or Tubular Steel
  The Curt Class II 1-1/4 Inch Ball Mount, part # C45015 has a solid steel shank. It has a 5 inch rise and measures 11-5/8 inches from the center of the hitch pin hole to the center of the ball hole. The other choices I have for a 1-1/4 inch ball mount with a 5 inch rise is the Curt Class II 1-1/4 Inch Ball Mount, part # C45014 which is 9-5/8 inches long and the Draw-Tite Class II 1-1/4 Inch Ball Mount, part # 36065 which is 10 inches long. Both of those ball mounts will also have solid...
  view full answer...
• Ball Mount For Thule Velospace XT3
  The Thule Velospace xt3 requires a 50mm Hitch Ball # EH53C-C. If you have a 2 inch hitch receiver you will need a mount like this one # BH20 or this one # C45015 for an 1-1/4 hitch.
  view full answer...
• Recommended Trailer Hitch For 2013 Chevrolet Camaro
  Unfortunately the only trailer hitches we have that are designed to work with your 2013 Camaro are Class l hitches. Class l hitches have a weight capacity of 200 lbs. You would want to check the owner's manual for the tow rating of your Camaro. I cannot recommend a trailer hitch for your Camaro that can handle the weight of your bike at 225 lbs, but if you do not have the ground effects package and you wish to tow a small motorcycle trailer behind your Camaro I recommend the Draw-Tite...
  view full answer...
• Trailer Hitch that Fits 2007 Audi A3 for Motorcycle Trailer
  For lighter duty vehicles like a 2007 Audi A3 there are only lighter duty hitches available like the Curt # C11192. Only way to use this as a tow vehicle will be to tow a small trailer which will also require lighting like the part # 46255. Even if a heavier duty hitch was made for the vehicle the vehicle itself wouldn't be able to handle the weight of the bike and carrier unsupported. The correct ball mount to use would be the part # C45015 as well.
  view full answer...
• What Solution Do You Have to Transport 1 SUP and 3 Kayaks On a Hyundai Kona?
  I have an option for you. For the combination of watersport accessories you want to transport, a roof rack solution is not possible. While the Hyundai Kona's owner manual does not recommend to use the vehicle for towing, the only option for two sit-in kayaks, one above-sit kayak, and a paddle board is the Malone MicroSport Trailer with Post Style Carriers # MAL24ZR. The MicroSport trailer will take away the headache of how to position/stack the paddleboard and kayaks on a roof rack system....
  view full answer...
• Will Curt Class II Ball Mount Fit into Draw-Tite Class I Trailer Hitch Receiver
  I just went out to our warehouse and installed the Curt Class II Ball Mount # C45015 into the Draw-Tite Trailer Hitch Receiver # 24796 and it fit perfectly. The Curt is 11-5/8 inches from the hitch pin hole to the hitch ball hole so it will work great for you. For a 2 inch hitch ball use # 19258 and for a 1-7/8 inch ball use # 19256. Then for a pin and clip use # F-4.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?