To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Concealed main body maintains your vehicle's factory look. Powder coated steel is sturdy and corrosion resistant.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
California residents: click here
Very happy with my hitch purchase from etrailer. The hitch shipped the same day I ordered it, and it arrived literally the next day.
The hitch included clear instructions and I installed it in about 90 minutes. Great experience from end to end with this purchase.
I have ordered several hitches from etrailer and been happy with all of them, including this one for my 2025 telluride.
Install took little under two hours including getting tools together and cleanup. Couple of suggestions after my install-
DO NOT cut the bumper piece per the instructions sheets. I marked it by their measurements and it looked odd - sure enough it would not have worked. I attached a photo, if you lay the piece upside side you can mark where to cut. You can’t see the cut after it’s installed unless you get on the ground, so don’t worry about getting it perfect.
The hardware on the exhaust side was the biggest pain. I had to torque from the nut side on the bolts that go through the frame. The socket extension from the other side was too long to manage by myself while holding the nut on the back side. And the heat shield on that side requires putting the washers on the hitch frame before passing the bolt through the washer and frame.
The video was very helpful. The printed instructions could use some updates. Example, it says there are four exhaust hangers to loosen but there are only three required.
Overall not too bad to install and I’m happy with the finished product. I didn’t have any shipping box issues like some have mentioned.
Put this on a 2025 Telluride. It was easy to install. I did have a buddy help hold things in place while I put the initial bolts in. Have used it several times to carry a hitch haul on the back. Works and looks great.
Very good overall. A few things others may want to consider. The packaging is poor. The hitch is shipped in a cardboard box with no protection, so there were some dings and scratches. Having a can of glossy black spray paint available for touch ups available is a good idea.
Watch the video(s) before attempting, they are a helpful supplement to the instructions provided.
A couple notes from my installation: I recommend removing the plastic bumper cover before you mount the receiver. After removing, mount and hand tighten the receiver with the four smaller bolts to determine the exact location of the hitch and then mark the location for the bumper cover cuts with a marker. You can remove the bumper cover by just removing two screws and two push pins. This allowed me to make much more accurate and clean cuts with an oscillating saw. You can reattach the bumper cover without having to take down the hitch.
The only significant challenge was installing and tightening the two long bolts above the muffler (passenger side) due to the heat shield making the space around the bolt heads very tight. I hand to use a punch to pound the reward most bolt into the hole since I couldn't fit it in by hand. Then, I couldn't fit a socket or the round part of a hand wrench around the bolt head since there's not enough space and I couldn't reach both sides of the bolt since the muffler is in the way. Ultimately, I found I could fit the crescent (open) side of a hand wrench around the bolt head and wedge it against the car's frame to keep it from spinning while I tightened the nut side with a socket wrench.
You may want to consider borrowing a powered right angle impact wrench - or at least have someone else hold the crescent wrench while you tighten the bolt with a socket wrench.
Lastly, I backed my Telluride up to the back of my (level) garage and used the downward slope of my driveway to give me a few extra inches of clearance to work. Ramps would have been much better. Borrow a set or use some blocks if possible.
Despite the challenges, it turned out great!
Brooke M.
1/29/2025
I love the detail! Thank you so much for taking the time to write all that out. Anyone who comes across your review is going to be glad they did because of all the info theyll glean. What all do you plan to use the hitch for?
Easy to install with the helpful video. Some parts are harder to access than others, but all the bolts lined up perfectly and no issues. It took me 1 hour or less for the whole thing with the rear wheels on blocks
Great hitch! Went in just like the description states. Love the fitment! I opted to leave the cover off instead of cutting it for now.
Hitch and wiring fit great.
The trailer hitch is well engineered and made, fit perfectly. Everything needed to do the installation was included. the only problem was it's not packaged very well and you'll need a can of black paint to touch up the scratches.
The hitch receiver works perfectly.
Was kind of tough to install by myself though. No fault of the hitch.
Scott
6/25/2025
No problems.
I followed the installation directions for our 2023 Kia Telluride hitch carefully. To facilitate installation, since I have no lift, I had the car extended over a down facing driveway apron and raised up on blocks. It was still a little challenging to get the parts behind the rubber exhaust pipe hangers. A car jack and ropes helped hold the hitch in place while the bolts were installed. You have to be bold when cutting a hole in the bumper for the hitch to stick through. Once installed, the hitch has worked perfectly on many bicycle excursions with either of the two Curt bicyle racks I purchased - a four bike hanger rack (which can handle three adult bikes) and a two bike flat rack. Especially for the price, this has been an excellent solution for us. I would comment on the bike racks separately.
Perfect fit nice detailed video of installation. However never 5 star only because nowhere to mount wire harness. All hitches should have some sort of mount even simple flat plate
This is the second hitch I purchased from etrailer and I am extremely satisfied with the video's provided on the website, which helped me decide on the specific hitch I wanted (this one mounted higher and required a minor cutting of the removable bumper panel which I wanted for a clean custom look and for use of my son's platform dirt bike carrier). The video's were "spot-on" and super accurate and easy to understand, which helped greatly with the installation. etrailer is a "top-notch" company and has accurate information for specific installations. The hitch arrived on time and in great condition (packaged appropriately for the delivery). The hitch is of great quality and workmanship (welds and finish). The instructions to install were accurate and easy to understand. The dimensions to cut the removable bumper panel were also accurate and easy to mark out. Installation came out perfect! I will always purchase my hitches from etrailer. I have recommended this company to two friends and they are both satisfied with the company and products purchased.
Hitch is 1/8 inch to narrow between the car frame. I was worried it might tweek the frame as I tried to tighten it to 79 ft-lbs torque. Now the right side rear passenger door trim is rubbing on front door trim when opening, so I think it did bend the frame ever so slightly. Also the trim cut-out template was incorrect for the width of the receiver. This was for a 2024 Kia Telluride EX. Other than that I think it will work out ok, not planning on doing any serious towing. The online videos were very helpful with the installation process.
Customer service at trailer is top notch! Although the box arrived damaged and parts of the hitch were scratched, but this is only the fault of the shipping company. Overall the hitch is in good shape and mounted perfectly on the Telluride. Good instructions, great videos from etrailer, and a solid product from Curt!
Purchased this for my 2020 Telluride and it fit perfectly. Everything lined up and the installation video was spot on. Definitely would recommend. My husband & I installed in a little over an hour.
Christine
4/30/2021
Perfectly!! I love it!! And recommend it to other Telluride Owners. One ordered and awaiting arrival.
This hitch looks and feels like a beast! Once installed and fasteners tightened it feels like it’ll tow every ounce of its rated weight.
I installed by myself in about 4 hours (which included a trip to Wally World to get a new jack when my husky decided it was done.
A couple of tips that I guarantee will make your install easier:
#1: DEFINITELY install/screw in the bolts on the exhaust (passenger) side FIRST. This is exactly what the instructions say to do, but me being the “genius” I am decided to forget about that part and screw in the driver side first.
2.) You would be well served to purchase an “exhaust hanger removal tool” for removing the hangers from the exhaust pipe. They’re all over Amazon for $16-$25. I recommend the Lisle 38350 pliers. $16.19 and 1-day shipping. If you have never dealt with removing exhaust hangers before, I promise you it will be worth every penny (even if you use it only once). It’ll save much time and many headaches.
3.) When it comes time to trim the bumper panel to allow room for the hitch, use a jigsaw with laminate blade. My cordless dewalt jigsaw w/laminate blade cut through the panel like butter and made getting a perfect fit very easy (see pictures). Obviously this requires removing the panel altogether, but I would recommend doing this regardless of what tool you’re using for the trimming.
Also, the included instructions for the 2022 Telluride version show the spare tire being lowered by using a wrench on the underside of the vehicle. While this is possible, it is exponentially easier to lower it by using a 13/16” socket on the bolt accessed from under the removable back floorboard panel (if my description of the location is confusing, see page 6-16 of the ‘22 Telluride Owner’s Manual for an illustration and better description).
Overall I give this 5 stars. I am by no means an expert (or even moderate, for that matter) “car guy”, and was able to install by myself in one day. That being said, I am above average in strength so don’t assume you will be able to do it alone - the hitch is pretty hefty (which of course is a good thing), especially when maneuvering it while on your back under the car.
If you follow the 3 tips listed above, I guarantee it will significantly reduce your install time and result in a cleaner, more professional look.
Everything is bolt on and extremely easy to install if you follow the video instruction or the instructions that come with the product. In addition to the hitch, I also got the harness which was easy to install. Thanks etrailer for making my family road trip happen.
Unbelievable delivery
I have not opened the box yet but so far all is well
Fit perfectly on my new 2025 telluride.
The hitch is great but this is my second time ordering through etrailer and I have been very impressed both times with the level of service.
There was a hiccup with our payment, but it was resolved.
Perfect fit for 2022 telluride s
Well recommended
Brooke M.
6/23/2025
That's awesome! Looks like you did a great job. What are you towing with the new hitch?
very easy to install
Perfect! Everything lined up as usual, my 3rd receiver from Etrairler. Order Tuesday at 3:00, got home in Pittsburgh at 3:30 on Thursday, it was on my porch. I’m 64 yrs old and installed it by myself in 1 1/2 hrs. Be prepared to cut a slot in the painted area of your bumper, you have to or the holes will not line up, trust me. Metric sockets and combo wrenches are a must. I used a hack saw and utility knife to cut my slot, worked well. Great help and service from Adam E.
Great instructions and super easy to install. Got delivered quickly!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Brooke M.
4/28/2025
Your experience here is basically the poster child for what we hope everyone can experience too! Thanks for sharing the photo -- hitch looks great!