UWS Truck Toolboxes
uws
Expert Answers about Uws
- Dimensions of UWS Crossover Toolbox for 2019 Ford F-350
- The UWS Deep Truck Bed Toolbox - Crossover Style - Low Profile Series - 10.8 cu ft - Gloss Black # UWS00376 measures just 17 inches deep at the bottom and 20 inches deep at the lid. I've attached the manufacturer dimensions in a photo to assist.
I did a little research on the Ford Superduty box length and it is 98 inches, so if you subtract the 17 inch box depth, you will have 81 inches (or 78 inches from the top of the box). If your Kawasaki Brute Force 750 is longer than that,...
view full answer... - Replacement Striker Pin and Bracket for UWS Truck Tool Box
- The Replacement Striker Bracket for UWS Truck Tool Boxes - Qty 1 # UWS-SBRACKET will use the Replacement Nail Head Striker Pin for UWS Boxes with Paddle Handles - 1/4" Diameter # C003-NHPIN.
view full answer... - How Does The UWS Standard Chest Stand Up To The Elements
- The UWS Chest part # UWS01022 is designed to be used in a cargo carrier outside in the elements. The extra-thick aluminum construction is rust resistant. UWS builds their boxes from sheets of 0.058" thick aluminum. Then they weld the seams for moisture and rain protection. You will also not see very much fading or sun damage with the aluminum material.
The UWS Chest measures 48" long x 20" wide x 20" deep so as long as your cargo rack is big enough this box will work well for your application....
view full answer... - Does the UWS Truck Bed Chest # UWS01040 Come with a Tray
- The UWS Truck Bed Chest # UWS01040 does not come with a tray.
I reached out to my contact at UWS to see if their tray would fit and he said that the only way you can get a similarly sized toolbox with a tray is to use part # UWS04543 instead. This comes with a sliding tray but it is a crossover style so it would take up space on your bed rails.
view full answer... - What Does UWS A-Frame Trailer Toolbox # UWS01065 Weigh
- The UWS A-Frame Trailer Toolbox # UWS01065 that you referenced weighs 37 lbs total. Other dimensions of it are 24" long (front) 49" long (rear) x 18" wide x 21" deep.
view full answer... - Can UWS Truck Bed Chest Tool Box # UWS01047 Fit 2017 Ford F-350 with 5th Wheel and Tonneau
- The overall height of the UWS Truck Bed Chest # UWS01047 is 17-1/4 inches which is going to be shorter than the height of your truck bedrails so it will pretty easily fit underneath your tonneau cover. Now without knowing the length of your bed and the fifth wheel hitch you have it's harder to say if the box would interfere but I can tell you that the box will take up 20 inches of your truck bed from the front of the bed back so you'd need to measure your truck bed to determine if that...
view full answer... - Replacement 501CH Key for Truck Tool Box
- We have exactly what you need.
For a replacement 501CH key for your truck tool box, you will use part # KEYCH501. If you need both the key and lock cylinder, you can use part # UWSLOCKCH501, which comes with the lock core and 2 keys.
view full answer... - Tool Box and Auxiliary Tank for 2018 Ram 3500 Long Bed
- If you want a single item that can both store tools and supply additional fuel capacity for your Ram 3500 long bed you might consider the DeeZee Combo Auxiliary Tank # DZ92740X. This unit combines a 43-gallon tank and a tool chest in one product that measures 54 long x 18 deep x 17-3/4-inches tall.
If you prefer to have the tool box near the rear of the bed then instead you could use the 38-gallon tank # DZ91752X at the cab and then use left and right black wheel well tool boxes # DZ95B...
view full answer... - Replacement Key for T-Handle Door Latch with CH545 Cylinder
- The Redline Replacement Key # CHK545 should be the correct key for the lock cylinder that is on your existing T-handle. This key is designed for T-handle locking door latches like what you have and the number matches up to the CH545 number you found on the cylinder. You will not have to replace the cylinder itself to use the key.
view full answer... - How Does UWS Notched Toolbox part # UWS01032 Install in Bed of Truck
- Typically the toolboxes like the UWS Notched part # UWS01032 that you referenced install by running nuts and bolts through the bottom of the box through the floor of the truck bed and then securing them underneath the bed.
view full answer... - Compatibiltiy of UWS Connector Rod with DeeZee Tool Box Latch
- I went out to our warehouse and tested the UWS Rod-Connector # UWSRODCONNECTOR with the Replacement Locking Latch for DeeZee Tool Boxes - Hook Style # DZTBLATCH1 to confirm they will work together.
view full answer... - Getting Two Lock Cylinders for UWS Toolbox Keyed Alike
- The replacement lock cylinders we have available for UWS Toolboxes like the cylinder # UWSLOCKCH510 you were looking at are each designed for a specific key number. This allows you to replace the existing lock core on your toolbox to match the key that you already have.
For example this Lock Cylinder # UWSLOCKCH510 uses key CH510. This number would be stamped onto the lock core itself.
With that being said if you are simply looking to replace the lock core on your UWS toolbox and...
view full answer... - How is UWS Truck Bed Chest # UWS01029 Installed in Truck Bed
- For chest style toolboxes like the UWS Truck Bed Chest # UWS01029 that you referenced you'll want to drill through the bottom of the box and truck bed to secure it using nuts and bolts. Other boxes will sometimes use j-hooks to secure in the truck bed but the chest style boxes have to drill through the truck bed.
view full answer... - Dimensions of UWS Replacement J-Bolt for Crossover Toolboxes # UWSJBOLT
- The part you referenced, UWS Replacement J-Bolt for Crossover Toolboxes # UWSJBOLT, measures 3-inches overall length, 1-inch wide and 3/16-inch in diameter.
Other j-bolts offered for other applications include part # RJBL at 9-1/2-inches long and # RJBS at 8-inches long which are Rhino-Rack spare tire carriers for use on their heavy-duty roof rack crossbars. These are both 1/2-inch diameter and include a matching nut.
view full answer... - What are the Dimensions of Replacement Locking T-Handle for UWS Toolboxes
- I went out to the warehouse and pulled a Replacement Locking T-Handle, # UWSTHLOCK, and took some measurements. The overall width is 4-3/4 inches. The overall height is 4-13/16 inches.
The mounting holes are 3-7/8 inches apart on center from side to side and 3-1/4 inches on center top to bottom.
The over depth from the back of the mounting surface to the end of the handle mechanism is 2-5/8 inches.
I made a picture for you that illustrates these dimensions.
view full answer... - What is Weight of UWS A-Frame Trailer Toolbox # UWS01064
- The UWS A-Frame Trailer Toolbox # UWS01064 that you referenced weighs 29 lbs. The dimensions are 20" long (front) 34" long (rear) x 18" wide x 21" deep and the cubic feet of storage that it holds is 4.1 cubic feet.
view full answer... - Recommended Lock Cylinder and Key for UWS Tool Boxes
- From what I can see from the photos, the latch itself seems to be in great condition just like the Replacement Locking T-Handle for UWS Toolboxes # UWSTHLOCK. So, it appears all you need is the lock cylinder and key. I recommend the Replacement Lock Cylinder for UWS Toolboxes w Square Paddle Handles # UWSLOCKCH503.
view full answer... - Can UWS Replacement Lock Assemblies Be Keyed Alike
- I believe the description should have stated one lock cylinder and two keys. You can order two locks that utilize the same key by entering a part number in the search box on the website like the # UWSLOCKCH506. You can order as many lock assemblies as you need that are keyed alike.
view full answer... - Dimensions of Replacement Lock Cylinder for UWS Toolboxes UWSLOCKCH507
- The Replacement Lock Cylinder for UWS Toolboxes # UWSLOCKCH507, which includes two matching keys, fits UWS tool boxes that have square paddle-style handles that look like part # UWSLOCKING.
To get you the dimensions you need I went to our warehouse and took several measurements of this part. I have indicated these dimensions on the linked photo, where possible.
Overall front-to-back depth, from the front of the lock face to the rear-facing side of the locking paddle, measures 7/8-inch....
view full answer... - Replacement CH507 Lock Cylinder Needed for T-Handle Style Latch Key
- Yes, you can acquire a replacement lock cylinder with the key number CH507 for a UWS T-handle style latch as part # UWS003-007THLC on our site. This comes with 2 replacement keys as well.
view full answer... - Replacement Keys for DeeZee Toolboxes
- A lot of brands of toolboxes use the same keys and locks. It is likely that replacement key # KEYCH504 will fit your DeeZee toolbox. UWS and DeeZee are different manufacturers though.
But to take the guess work out all you need is # DZKEY. Just type the key number where indicated on the page and you will get 2 replacement keys to match the lock number.
view full answer... - Replacement Lock and Keys for UWS Toolboxes
- There are several different lock and key replacements for UWS toolboxes and each one is different from the next. There is a chance you could end up with the same lock and key that you already have on the box but you would just need to order a different number than what is printed on the lock face or key to get a completely different set.
For example, if you ordered # UWSLOCKCH503 you would get a lock and keys for CH503. I have included part links to all of the replacements we have for...
view full answer... - Dimensions of Part # UWSRODCONNECTOR
- The # UWSRODCONNECTOR is the only rod connector we carry. I did include a link to replacement parts for toolboxes that we do carry.
For the rod connector, I pulled one from the warehouse to take some measurements.
Take a look at the photo I produced showing the dimensions.
view full answer... - CH505 Key Availability for UWS Tool box
- If you only need replacement keys marked CH505 you would only need the part # KEYCH505 instead of the part # UWSLOCKCH505 which also includes the lock.
view full answer... - Replacement Lock Cylinder for a UWS Toolbox
- As long as the paddle handle on your UWS toolbox looks like the photo that I have attached, you can use the UWS Replacement Lock Cylinder, # UWSLOCKCH509. This lock comes with 2 keys.
If you still have your old keys, there will be a number on them that starts with the letters CH. If you can send me the numbers on your keys, I can see if we have a lock cylinder that matches your old keys.
view full answer... - Recommended Replacement Lock Cylinder and Keys for Truck Side Box
- Replacement Lock Cylinder for UWS Toolboxes w Square Paddle Handles - CH503, # UWSLOCKCH503 is the lock cylinder you are looking for. Your picture was a huge help to ensure we recommended the right replacement for your toolbox. This kit comes with both one cylinder and two keys.
view full answer... - What are the Measurements of the UWS Twist Lock When it is Closed
- When closed the lock # UWSTWISTLOCK is 1-7/8 inches tall and 1-1/2 inches wide. I included a picture showing this and other relevant measurements for you.
view full answer... - Pipe or Tubing Used w/ UWSSTACHONS for Toolbox Grab Rails
- The # UWSSTACHONS uses 7/8 inch diameter tubing or pipe which isn't included. The length of pipe would depend on what you decided to use.
view full answer... - Availability of Replacement Lift Cylinder for UWS Single Lid Tool Box
- I spoke with my contact at UWS and they said that the UWS Replacement Lift Cylinder, part # UWSLIFTCYLIND, will fit all of the UWS toolboxes. The name on the lifts could change if they switch to a different supplier.
view full answer... - Replacement Lock Cylinder for UWS Toolboxes w Square Paddle Handles CH510 Recommendation
- Based on the number you mentioned of CH510 you'd want our Replacement Lock Cylinder for UWS Toolboxes w Square Paddle Handles # UWSLOCKCH510.
view full answer...
What our customers are saying:
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI