Towing Capacity Of etrailer Anti-Rattle Hitch Collar

Question

Question:

What is the maximum capacity of your anti-rattle hitch collar? Does this reduce towing capacity?

asked by: Scott L

0

Expert Reply:

Hey Scott! The etrailer Anti-Rattle Hitch Collar # e55YV is rated for up to 10,000 lbs gross trailer weight and won't reduce the capacity of a properly matched towing setup. As always, your actual towing capacity is determined by the lowest-rated component in the entire system.

What kind of truck do you have and what are you typically towing?

expert reply by: Robin H

0

etrailer Anti-Rattle Hitch Collar
(click to enlarge)

James C.

8/9/2026

Hey Robin, Since Scott doesn't seem interested in continuing this conversation, I'd like to shoe-horn in. I have a 2016 Silverado 3500 HD, tow capacity 14000 lbs. I'm using the Curt Rebellion XD, part number C57UR, with a rated capacity of 20000 lbs. I understand go by the lowest rating in the tow system, so don't exceed 14000 lbs. Questions for you, though, regarding the E-Trailer Anit-rattle hitch collar, part number e55YV-- 1) Why is there a weight rating for the collar? The collar is not a load carrying member, so what does it matter how much the trailer weighs? Skimming through other available anti-rattle offerings, it doesn't appear that any of them have published weight limits. 2) If I were to exceed the collar's load rating of 10000 lbs, what is likely to happen? The wedge breaks and the hitch begins to rattle again, or am I missing something?

Robin H.

8/10/2026

@JamesC if the gross towing weight goes over 10k it is too much pressure for the collar's gate. The pins can also bend and eventually break. Realistically, if you overload the anti-rattle towing something at your max capacity it will wear it down slowly. You could compensate by tightening more but eventually it will fail. The solution here is to not tighten it down on a heavier trailer if you're using it. It can remain installed on the receiver and nothing will happen. If you exceed the 10k rating and it breaks, the only thing that happens is it stops working. There are no safety concerns. We tested it using SAE J684 standards and it falls under Class 4 which is up to 10,000 lbs. If I had to guess on other anti-rattle devices, they either haven't tested it, aren't concerned that the weight would damage it, or aren't worried about it if it actually does since it isn't a safety concern.

James C.

8/12/2026

@RobinH thanks for the information. I wish all manufacturers had tech support and were as transparent about their testing criteria as you guys.

Robin H.

8/13/2026

@JamesC thanks, and I completely agree. I deal with manufacturers pretty regularly myself, so I know how frustrating it can be when you can’t get a clear answer to what should be a straightforward question. We want to be as transparent as possible about our products and how they’ve been tested. We’re always looking for ways to improve them and make sure they meet the standards we expect before we recommend them. If you need anything else, don’t hesitate to reach out!

Answer 1

Hi Kristian, great question! The etrailer Anti-Rattle Hitch Collar, part #e55YV, works by taking the slack out between your hitch receiver and the shank of your ball mount or hitch-mounted accessory. It clamps around the outside lip of your 2-1/2…

view full answer...

Answer 2

Hey Mike, congratulations on the new truck! You can definitely use the two together. The Curt StowPro 2-Ball Mount #C34FR53HY uses a standard 2-1/2" shank, making it a great match for our etrailer Anti-Rattle Hitch Collar #e55YV. It installs…

view full answer...

Answer 3

Hey Greg! The etrailer Anti-Rattle Hitch Collar for 2.5" Hitch Receivers #e55YV is not compatible with a weight distribution hitch. This is really the only restriction for our anti-rattle. If you need an anti-rattle for a weight distribution…

view full answer...

Answer 4

Hey Joe! I asked our Product Development team for a little more info on this for you and the etrailer Anti-Rattle Hitch Collar for 2.5" Hitch Receivers #e55YV reducer is yellow zinc coated steel and just to add a little more info, the…

view full answer...

Answer 5

The Camco 90 degree elbow fitting #CAM57633 is designed for use with LP gas systems (propane) so I do not see any reason why you can't use it. It should work just fine for you provided it is the right size needed. It has a 3/8" female swivel…

view full answer...

Answer 6

There are several methods to try and determine the amount of liquid propane remaining in a tank. The first is a pressure gauge like the Camco #CAM59023. This reads the pressure of vapor propane which remains steady until mostly empty then the needle…

view full answer...

Answer 7

The Camco Propane Cylinder Gas Gauge and Leak Detector #CAM59023 doesn't have the ability to shut off in the event of a leak. It's simply going to show you that there's a leak because the gauge reads as propane flows through it. The…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Towing Capacity Of etrailer Anti-Rattle Hitch Collar

Product Page this Question was Asked From

Continue Researching