Headlight Protection Film Specs:
Features:
Apply LampGard to your headlamps, fog lamps, turn-signal lights or parking lights and never worry about scratching, cracking or pitting again. This tough, UV-resistant cover installs in seconds directly to the lamp surface for complete protection.
More Information >Headlight Protection Film Specs:
Features:
Apply LampGard to your headlamps, fog lamps, turn-signal lights or parking lights and never worry about scratching, cracking or pitting again. This tough, UV-resistant cover installs in seconds directly to the lamp surface for complete protection.
More Information >Videos
for Headlight Protection Film
Help Articles
for Headlight Protection Film
Expert Answers
for Headlight Protection Film
You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it…
view full answer...For your 2022 Ram 2500 I recommend going with the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item #AL88289 over the Firestone item #F2598. These have a 5,000 lbs weight capacity and the air springs have…
view full answer...The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.
view full answer...Yes, the etrailer SD Non-Binding Tow Bar for Blue Ox Base Plates #e47ZR would have enough adjustability between the 1-1/2" shank rise/drop and the 3" of tilt to meet your 4" difference.…
view full answer...The Blue Ox Acclaim Non-Binding Tow Bar #BX4330 is compatible with Blue Ox base plates that are between 23" and 30" apart on center. Since you're measuring 34" on…
view full answer...The 16 inches of height that the Yakima SkyBox NX 16 Cargo Box #Y95AV that you referenced would be the height above the crossbars of your 2005 GMC Yukon Denali. I attached a review video for this cargo box for you to check out also.
view full answer...When adjusting the arms of the #BWRVK3305, you have the option of setting up so the king pin will sit 3 inches forward or 1 inch forward of the axle. I'd set it up at the tallest height, 18-3/4 inches above the floor of the truck…
view full answer...You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...The B and W Turnover Ball hitch part #BWGNRK1309 is a confirmed fit for your 2015 Ram 1500 with an EcoDiesel engine. Since your truck has a such a short bed you are going to want to use the offset adapter part #BWGNXA4685 as well. Hopefully the…
view full answer...I recommend using the Fastway e2 Weight Distribution #FA92-00-0800 for your 7x14 Interstate Loadrunner tandem axle trailer. This hitch is rated for trailers up to 8,000lbs with a tongue weight between 400-800lbs. If your unloaded tongue weight is…
view full answer...When we installed the Curt Hitch #C12091 on a 2015 Ford Fusion we found that from the top of the hitch opening down to the ground it measured 11-1/2 inches. From the bottom of the hitch to the ground would be about 10 inches. I attached an install…
view full answer...Filter Products (4)