...CAN YOU GIVE ME LUG NUT TORQUE FOR MY DEXTER 16,000 LB AIR BRAKE AXLES?
THE NUTS ARE 1-5/16
IT LOOKS LIKE THEY HAVE A BUILT IN ROUNDED WASHER?
I HAVE A PICTURE OF THE AXLE END AND THE LUG NUT...
Hey Greg, yes the Aluminum Hi-Spec Series 04 Star Mag Trailer Wheel #AM20258 that you referenced would work with a Load Range E tire ST175/80R13 like you mentioned.
Technically, yes Steve, the Electric Trailer Brake Assembly for Lippert ABS Hubs - 12" 5.2K - 7K #LC83PX will physically fit the same 4-bolt mounting flange and 12inch drums. But here’s the catch: if your hubs don’t have the ABS ring, then the…
The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
Hi Jeff; I'm assuming you were able to identify the parts based on the axle tag or by pulling off the hubs and measuring. Did you verify that the grease seal had a 2.25" inner diameter? The #AKIHUB-655-6-EZ-K comes with a 2.25" ID…
To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
Hi Jeff, welcome back! Is that the 126003? I don't see a 1260031 but the Lippert 126003 is a 3,500 lb hub with a 5 on 4-1/2 bolt pattern. Assuming that is correct, the Terran Axle Trailer Hub and Drum Assembly #TX68VJ will work as a replacement.…
There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…
...CAN YOU GIVE ME LUG NUT TORQUE FOR MY DEXTER 16,000 LB AIR BRAKE AXLES?
THE NUTS ARE 1-5/16
IT LOOKS LIKE THEY HAVE A BUILT IN ROUNDED WASHER?
I HAVE A PICTURE OF THE AXLE END AND THE LUG NUT...
Hey Greg, yes the Aluminum Hi-Spec Series 04 Star Mag Trailer Wheel #AM20258 that you referenced would work with a Load Range E tire ST175/80R13 like you mentioned.
Technically, yes Steve, the Electric Trailer Brake Assembly for Lippert ABS Hubs - 12" 5.2K - 7K #LC83PX will physically fit the same 4-bolt mounting flange and 12inch drums. But here’s the catch: if your hubs don’t have the ABS ring, then the…
The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
Hi Jeff; I'm assuming you were able to identify the parts based on the axle tag or by pulling off the hubs and measuring. Did you verify that the grease seal had a 2.25" inner diameter? The #AKIHUB-655-6-EZ-K comes with a 2.25" ID…
To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…
Hi Jeff, welcome back! Is that the 126003? I don't see a 1260031 but the Lippert 126003 is a 3,500 lb hub with a 5 on 4-1/2 bolt pattern. Assuming that is correct, the Terran Axle Trailer Hub and Drum Assembly #TX68VJ will work as a replacement.…
There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…
Durable Trailer Hubs and Drums for 6,000 lbs Axles
Explore robust trailer hubs and drums designed for 6,000 lbs axles. Perfect for upgrading or replacing parts on your trailer, these components ensure reliable performance and ease of installation. Ideal for enthusiasts looking to enhance their trailer's c
Yes, many users choose galvanized hub and drum assemblies for their rust and corrosion resistance, especially when launching boats in fresh water. This makes them a great choice for trailers frequently exposed to wet conditions, ensuring longevity and reliability.
While some kits include bearings, it's important to verify before purchasing. Bearings are crucial for smooth operation, and having them included can save time and ensure compatibility. Always check the product details to confirm what's included in your purchase.
To ensure a perfect fit, measure your current axle and spindle dimensions, and compare them with the product specifications. Some users have had to switch out seals for a precise fit, so having the correct measurements will help avoid any installation issues.
Hubs and drums for 6,000 lbs axles offer enhanced durability and load capacity, making them ideal for heavy-duty trailers. They provide a solid foundation for safe towing, especially when upgrading from lighter axles. This ensures your trailer can handle more weight without compromising performance.
When upgrading, consider the type of brakes your trailer needs. Electric brakes are often preferred for their efficiency and control. Ensure the hubs and drums are compatible with your braking system, and adjust the brake tension properly for optimal performance.
Filters
